Home › General › MAINTENANCE › GF2A TRANSFER OIL
RM37A0E _V1 General _086848 MAINTENANCE _0420310 GF2A TRANSFER OIL A

MAINTENANCE  GF2A TRANSFER OIL  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN TRANSFER OIL

a.

Stop the vehicle on a level surface.


b.
C426185

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket from the transfer assembly.


c.
C426186

Using a 10 mm hexagon socket wrench, remove the transfer drain plug and gasket from the transfer assembly and drain the transfer oil.


d.

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, temporarily install the transfer filler plug and gasket to the transfer assembly.

HINT:

Reuse the old gasket as the transfer filler plug will be removed again.



e.

Using a 10 mm hexagon socket wrench, install the transfer drain plug and a new gasket to the transfer assembly.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 2.ADD TRANSFER OIL

a.

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket from the transfer assembly.


b.

Add transfer oil.

Oil Type:

Toyota genuine differential gear oil LX


Standard Capacity (for Reference):

0.39 liters (0.41 US qts, 0.34 Imp. qts)


NOTICE:

Using transfer oil other than the specified oil may cause abnormal noise or vibration, or damage the transfer of the vehicle.



c.
C278961C01
2.667,0.854 2.979,1.052 0.313,0.198 10 false *a
*a 0 to 5 mm (0 to 0.197 in.)


Pour transfer oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the transfer filler plug hole.

NOTICE:
·

When adding transfer oil, pour it slowly.

·

Add transfer oil a little at a time, waiting several minutes between each addition of transfer oil.

·

Too much or too little transfer oil will lead to transfer problems.




d.

Wait approximately 5 minutes and check that the oil level has not changed.


e.
C426187C01
0.5,4.417 0.396,4.417 0.396,4.417 0.396,4.167 false 0.417,3.99 0.417,3.448 0.417,3.448 0.531,3.448 false 1.063,3.958 1.063,3.177 1.063,3.177 1.177,3.177 false 0.542,4.323 0.854,4.479 0.313,0.156 10 false *a 0.573,3.365 0.885,3.521 0.313,0.156 10 false *b 2.083,3.354 2.396,3.51 0.313,0.156 10 false *c 1.271,3.094 1.583,3.26 0.313,0.167 10 false SST
*a 10 mm Straight Hexagon Wrench
*b 10 mm Union Nut Wrench
*c Torque Wrench Fulcrum Length


Using SST, a 10 mm straight hexagon wrench and 10 mm union nut wrench, install the transfer filler plug and a new gasket to the transfer assembly.

SST
09961-00950  

Torque:
Specified tightening torque : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

After adding transfer oil, drive the vehicle and recheck the oil level.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 19.9 N*m (203 kgf*cm, 15 ft.*lbf)




Hide 3.INSPECT FOR TRANSFER OIL LEAK