Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT
RM37A0E _53 Suspension _086865 FRONT SUSPENSION _0420323 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

for HV Model

Auxiliary battery terminal is disconnected/reconnected


Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Front wheel alignment adjustment
for HV Model

Perform "Calibration".


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

NOTICE:
for HV Model
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43330K 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C424020

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C424021

Remove the cotter pin.


c.

Remove the nut.


d.
C424022C01
1.063,0.083 1.458,0.083 1.458,0.083 1.458,0.969 true 1.313,0.094 1.313,0.969 true 3.042,0.927 3.354,1.083 0.313,0.156 10 false *a 0.771,0.031 1.229,0.229 0.458,0.198 10 false SST
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



e.
C424023C01
1.469,1.354 1.885,1.354 false 0.969,4.469 1.083,4.469 1.083,4.469 1.083,4.083 false 2.302,2.646 2.698,1.979 2.698,1.979 2.792,1.979 true 1.563,1.771 2.167,1.771 false 0.531,4.469 0.615,4.469 0.615,4.469 0.615,3.865 true 0.813,4.375 1.125,4.531 0.313,0.156 10 false *a 2.302,0.74 2.615,0.896 0.313,0.156 10 false *b 1.313,1.26 1.625,1.417 0.313,0.156 10 false *c 2.833,1.906 3.146,2.063 0.313,0.156 10 false *d 2.302,0.375 2.615,0.531 0.313,0.156 10 false *b 2.083,3.729 2.396,3.885 0.313,0.156 10 false B 2.083,3.448 2.396,3.604 0.313,0.156 10 false A 2.208,1.698 2.667,1.896 0.458,0.198 10 false SST 0.385,4.375 0.698,4.573 0.313,0.198 10 false *e
*a Center Nut
*b Molybdenum Grease Application Area
*c Place wrench here
*d String
*e Spacer
V113147

Turn


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the front axle assembly to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.

·

Make sure that SST is securely positioned on the spacer.

·

If the steering knuckle spacer has come off, replace the steering knuckle with a new one.