Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417738 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

The main power source for the main body ECU (multiplex network body ECU) is supplied via the door control battery.

WIRING DIAGRAM

B487341E10
1.635,1.188 2.531,1.573 0.896,0.385 10 false from Auxiliary Battery 3.302,1.344 3.688,1.604 0.385,0.26 10 false D/L 2.781,2.448 3.927,2.729 1.146,0.281 10 false ECU-DCC NO. 2 1.427,4.271 3.031,4.74 1.604,0.469 10 false Instrument Panel Junction Block Assembly 0.146,5.469 0.76,5.729 0.615,0.26 10 false MB 0.146,5.635 1.781,6.125 1.635,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 5.427,5.479 6.042,5.74 0.615,0.26 10 false H45 5.427,5.646 6.781,6.083 1.354,0.438 10 false Door Control Battery 5.5,4.688 6.115,4.948 0.615,0.26 10 false GND1 5.49,3.469 6.104,3.729 0.615,0.26 10 false EDOR 5.49,2.302 6.104,2.563 0.615,0.26 10 false BECU 5.49,1.198 6.104,1.458 0.615,0.26 10 false BATB 4.042,0.969 4.656,1.229 0.615,0.26 10 false 3 3.979,1.188 4.594,1.448 0.615,0.26 10 false 4A 3.99,2.073 4.604,2.333 0.615,0.26 10 false 22 3.99,2.281 4.604,2.542 0.615,0.26 10 false 4B 2.76,3.25 3.375,3.51 0.615,0.26 10 false 23 2.76,3.458 3.375,3.719 0.615,0.26 10 false 4B 0.938,3.5 1.552,3.76 0.615,0.26 10 false BECU 1.427,3.354 2.042,3.615 0.615,0.26 10 false 31 5.292,1.083 5.906,1.344 0.615,0.26 10 false 5 5.292,2.177 5.906,2.438 0.615,0.26 10 false 4 5.302,3.354 5.917,3.615 0.615,0.26 10 false 3 5.292,4.552 5.906,4.813 0.615,0.26 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing the following inspection, perform Initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - BATTERY AND BODY GROUND)
a.

Disconnect the H45 door control battery connector.


b.
B533172C04
1.385,0.135 1.792,0.438 0.406,0.302 2.583,1.833 2.417,1.833 2.417,1.833 1.917,1.188 false 2.083,2 1.917,2 1.917,2 1.75,1.188 false 1.104,1.833 1.25,1.833 1.25,1.833 1.417,1.188 false 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 1.458,0.198 1.771,0.396 0.313,0.198 10 false H45 2.635,1.75 3.25,1.948 0.615,0.198 10 false BATB 2.135,1.917 2.75,2.115 0.615,0.198 10 false BECU 0.719,1.75 1.333,1.948 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Door Control Battery)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-5 (BATB) - Body ground Ignition switch off*1
Always*2
11 to 14 V
H45-4 (BECU) - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-2 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (EDOR) - 4B-23 Always Below 1 Ω
H45-3 (EDOR) or 4B-23 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Reconnect the H45 door control battery connector.


b.

Turn the ignition switch off.


c.

Remove the ECU-DCC NO. 2 fuse and leave the vehicle as is for 50 minutes.


d.
B508352C13
1.469,0.146 1.917,0.375 0.448,0.229 1.813,0.948 2.146,0.271 2.146,0.271 2.49,0.271 false 1.563,0.177 2.177,0.375 0.615,0.198 10 false H45 2.552,0.188 3.167,0.385 0.615,0.198 10 false EDOR 0.458,0.583 0.771,0.781 0.313,0.198 10 false *a
*a Component with harness connected
(Door Control Battery)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-3 (EDOR) - Body ground Ignition switch off Below 2 V



Result:
Proceed to
OK
NG



OK

4.INSPECT DOOR CONTROL BATTERY (INTERNAL CIRCUIT)

NG

REPLACE DOOR CONTROL BATTERY

4.INSPECT DOOR CONTROL BATTERY (INTERNAL CIRCUIT)
a.

Install the ECU-DCC NO. 2 fuse.


b.
B508352C14
1.469,0.146 1.917,0.375 0.448,0.229 1.802,0.948 2.146,0.271 2.146,0.271 2.49,0.271 false 1.542,0.167 2.156,0.365 0.615,0.198 10 false H45 2.552,0.188 3.167,0.385 0.615,0.198 10 false EDOR 0.458,0.583 0.771,0.781 0.313,0.198 10 false *a
*a Component with harness connected
(Door Control Battery)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-3 (EDOR) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE DOOR CONTROL BATTERY

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU).

B417873C22
1.948,0.885 2.354,1.125 0.406,0.24 5.417,0.719 5.823,0.958 0.406,0.24 3.521,2.292 3.667,2.292 3.667,2.292 3.781,1.656 false 0.219,0.156 0.531,0.354 0.313,0.198 10 false *a 5.521,0.75 5.833,0.948 0.313,0.198 10 false 4B 2.042,0.906 2.354,1.104 0.313,0.198 10 false MB 3.083,2.208 3.604,2.427 0.521,0.219 10 false BECU
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-31 (BECU) - 4B-23 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY