Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086895 SEAT BELT _0420373 SEAT BELT WARNING SYSTEM G

SEAT BELT  SEAT BELT WARNING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

w/ Buzzer Regulated by Law:

i.

Turn the ignition switch to ON.


ii.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

Check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


iii.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


iv.

Turn the ignition switch to ON (READY).


v.

Check the state of the seat belt warning light on the combination meter assembly under the following conditions:

1.

Step 1:

When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released, check that the seat belt warning light on the combination meter assembly blinks.

2.

Step 2:

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

After 90 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

3.

Step 3:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

4.

Step 4:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

5.

Step 5:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.




b.

w/o Buzzer Regulated by Law:

i.

Turn the ignition switch to ON.


ii.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.


iii.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


iv.

Start the engine.


v.

When the driver seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.


vi.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 24 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 100 seconds and then illuminates.


vii.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.



Hide 2.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

w/ Buzzer Regulated by Law:

i.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and allow it to come into contact with the seatback.



ii.

Fasten the driver seat belt.


iii.

Turn the ignition switch to ON.


iv.

When the front passenger seat belt is not fastened with the front passenger seat occupied, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

Check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


v.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


vi.

Turn the ignition switch to ON (READY).


vii.

Check the state of the seat belt warning light on the combination meter assembly under the following conditions:

1.

Step 1:

When the front passenger seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released, check that the seat belt warning light on the combination meter assembly blinks.

2.

Step 2:

When the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

After 2 minutes, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

3.

Step 3:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

4.

Step 4:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

5.

Step 5:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, the front passenger seat belt not fastened and the weight on the front passenger seat, check that the seat belt warning light on the combination meter assembly turns off when the weight is removed from the front passenger seat.

6.

Step 6:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.




b.

w/o Buzzer Regulated by Law:

i.

Turn the power switch on (IG).


ii.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



iii.

Fasten the driver seat belt.


iv.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


v.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


vi.

Start the engine.


vii.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 24 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 100 seconds and then illuminates.


viii.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.



Hide 3.INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning)

a.
B567214C01
0.938,1 1.104,1 1.104,1 1.438,1.25 false 1.938,1.26 2.354,1.01 2.354,1.01 2.521,1.01 false 1.896,1.5 1.896,1.833 1.896,1.833 2.063,1.833 false 1.688,1.302 1.688,1.969 1.688,1.969 1.854,1.969 false 1.458,1.49 1.458,1.823 1.458,1.823 1.292,1.823 false 0.271,0.167 0.583,0.323 0.313,0.156 10 false *1 0.792,0.885 1.104,1.042 0.313,0.156 10 false *a 1.917,1.896 2.229,2.052 0.313,0.156 10 false *b 2.552,0.917 2.865,1.073 0.313,0.156 10 false *c 1.135,1.729 1.448,1.885 0.313,0.156 10 false *d 2.125,1.729 2.438,1.885 0.313,0.156 10 false *e
*1 Rear Seat Belt Warning Light (Telltale Light Assembly)
*a Rear No. 1 Seat LH
*b Rear No. 1 Seat Center
*c Rear No. 1 Seat RH
*d Rear No. 2 Seat LH
*e Rear No. 2 Seat RH


Check the state of the rear seat belt warning light on the radio receiver assembly under the following conditions:

i.

Turn the ignition switch off.


ii.

Turn the ignition switch to ON.


iii.

When a rear No. 1 seat belt or a rear No. 2 seat belt is not fastened, check that the rear seat belt warning light on the telltale light assembly is illuminated.


iv.

After 66 seconds, check that the rear seat belt warning light on the telltale light assembly turns off.


v.

When one of the rear No. 1 seat belt or rear No. 2 seat belt is unfastened from being fastened, check that the rear seat belt warning light on the telltale light assembly illuminates.



Hide 4.INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

for Front Seat Belt Warning Buzzer (w/ Buzzer Regulated by Law):

i.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and allow it to come into contact with the seatback.



ii.

After turning the ignition switch to ON, wait for approximately 1.8 seconds with the driver seat belt not fastened check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.


iii.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


iv.

Turn the ignition switch to ON (READY).


v.

When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds once.


vi.

When 24 seconds have passed after the buzzer sounded, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.


vii.

After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.


viii.

Check that the seat belt warning buzzer in the combination meter assembly stops 96 seconds after it started sounding at an interval of 1.2 seconds.


ix.

After the seat belt warning buzzer in the combination meter assembly stops and the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt fastened, when the driver or front passenger seat belt is unfastened, check that the buzzer sounds once again and then sounds according to the appropriate pattern.


x.

After the seat belt warning buzzer in the combination meter assembly stops sounding, move the shift lever to R, and then move it to D. Drive the vehicle at 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened, and check that the buzzer sounds once again and then sounds according to the appropriate pattern.



b.

for Front Seat Belt Warning Buzzer (w/o Buzzer Regulated by Law):

i.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



ii.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


iii.

Start the engine.


iv.

When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 24 seconds.


v.

After the seat belt warning buzzer has been sounding for 24 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 100 seconds.


vi.

Check that the seat belt warning buzzer in the combination meter assembly stops 124 seconds after it started sounding at an interval of 1.2 seconds.


vii.

After the seat belt warning buzzer in the combination meter assembly stops and the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt fastened, when the driver or front passenger seat belt is unfastened, check that the buzzer sounds according to the appropriate pattern.


viii.

After the seat belt warning buzzer in the combination meter assembly stops sounding, move the shift lever to R, and then move it to D. Drive the vehicle at 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened, and check that the buzzer sounds according to the appropriate pattern.



c.

for Rear Seat Belt Warning Buzzer (w/o Buzzer Regulated by Law):

i.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


ii.

Fasten the driver seat belt.


iii.

Start the engine.


iv.

Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the seat belt warning buzzer in the combination meter assembly sounds once.


v.

After the seat belt warning buzzer sounded once, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.


vi.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 60 seconds.


vii.

Check that the seat belt warning buzzer in the combination meter assembly stops 66 seconds after it started sounding at an interval of 1.2 seconds.


viii.

After the seat belt warning buzzer in the combination meter assembly stops, turn the ignition switch off, open and close either rear door and then start the engine. Drive the vehicle at approximately 20 km/h (12 mph) or more while a rear seat belt is not fastened and check that the buzzer sounds again.


ix.

After the seat belt warning buzzer in the combination meter assembly stops, fasten a rear seat belt, drive the vehicle at approximately 20 km/h (12 mph) or more, unfasten the rear seat belt and check that the buzzer sounds in the same pattern again.


x.

After the seat belt warning buzzer in the combination meter assembly stops, stop the vehicle, change the shift lever to R and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.