Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420540 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

for HV Model

This circuit is from the No. 2 skid control ECU (brake actuator assembly) to the radio and display receiver assembly.


for Gasoline Model

This circuit is from the skid control ECU (brake actuator assembly) to the radio and display receiver assembly.


WIRING DIAGRAM

for HV Model
E372242E91
2.302,1.479 2.906,1.719 0.604,0.24 10 false A57 2.302,1.646 4.219,2.135 1.917,0.49 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 3.688,0.99 4.292,1.229 0.604,0.24 10 false 24 5.219,1.99 5.823,2.229 0.604,0.24 10 false H2 5.219,2.146 6.406,2.594 1.188,0.448 10 false Radio and Display Receiver Assembly 5.417,1.083 6.021,1.323 0.604,0.24 10 false PKB 5.146,0.99 5.75,1.229 0.604,0.24 10 false 20 3.177,1.104 3.781,1.344 0.604,0.24 10 false EPBW

for Gasoline Model
E372242E84
2.438,1.479 3.042,1.719 0.604,0.24 10 false A39 2.427,1.635 3.969,2.104 1.542,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 3.688,0.99 4.292,1.229 0.604,0.24 10 false 24 5.219,1.99 5.823,2.229 0.604,0.24 10 false H2 5.219,2.146 6.406,2.594 1.188,0.448 10 false Radio and Display Receiver Assembly 5.417,1.083 6.021,1.323 0.604,0.24 10 false PKB 5.146,0.99 5.75,1.229 0.604,0.24 10 false 20 3.156,1.104 3.76,1.344 0.604,0.24 10 false EPBW

PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

2.CHECK BRAKE WARNING LIGHT

B

4.CHECK BRAKE WARNING LIGHT
2.CHECK BRAKE WARNING LIGHT
a.

Check that the brake warning light comes on when the parking brake is applied and goes off when it is released.

OK:

The brake warning light operates as specified above.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-20 (PKB) - A57-24 (EPBW) Always Below 1 Ω
H2-20 (PKB) or A57-24 (EPBW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BRAKE WARNING LIGHT
a.

Check that the brake warning light comes on when the parking brake is applied and goes off when it is released.

OK:

The brake warning light operates as specified above.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-20 (PKB) - A39-24 (EPBW) Always Below 1 Ω
H2-20 (PKB) or A39-24 (EPBW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR