Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420540 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E360461E99
1.344,0.5 1.521,0.677 0.177,0.177 10 false 9 0.875,1.458 1.49,1.656 0.615,0.198 10 false UDO+ 0.906,2.219 1.521,2.417 0.615,0.198 10 false UJSS 5.906,2.219 6.521,2.417 0.615,0.198 10 false USG1 5.906,1.458 6.521,1.656 0.615,0.198 10 false US1+ 5.906,0.656 6.521,0.854 0.615,0.198 10 false US1- 0.042,2.688 0.656,2.885 0.615,0.198 10 false H15 0.052,2.865 2.542,3.146 2.49,0.281 10 false No. 1 Stereo Jack Adapter Assembly 2.479,3.271 5.083,3.5 2.604,0.229 10 false : USB Communication Line 3.552,1.76 4.188,1.979 0.635,0.219 10 false * 5.833,2.677 6.448,2.875 0.615,0.198 10 false H100 5.833,2.875 7.031,3.344 1.198,0.469 10 false Radio and Display Receiver Assembly 5.729,0.542 5.906,0.719 0.177,0.177 10 false 2 1.333,1.323 1.51,1.5 0.177,0.177 10 false 10 1.354,2.094 1.531,2.271 0.177,0.177 10 false 12 5.75,2.115 5.927,2.292 0.177,0.177 10 false 5 5.74,1.323 5.917,1.5 0.177,0.177 10 false 3 0.906,0.656 1.521,0.854 0.615,0.198 10 false UDO- 0.281,3.281 1.125,3.51 0.844,0.229 10 false *: Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the H100 radio and display receiver assembly connector.


b.

Disconnect the H15 No. 1 stereo jack adapter assembly connector.


c.
E429894C02
1.563,2.219 1.906,2.458 0.344,0.24 1.542,0.208 1.958,0.479 0.417,0.271 2.135,1.938 1.781,1.49 false 1.844,1.354 2.26,1.5 false 1.115,1.667 1.583,1.313 false 1.417,4.083 1.656,3.76 false 0.969,4.063 1.646,3.667 false 2.135,4 1.792,3.656 false 0.24,0.188 0.552,0.385 0.313,0.198 10 false *a 0.24,2.802 0.552,3 0.313,0.198 10 false *b 0.76,1.625 1.188,1.833 0.427,0.208 10 false US1+ 2.188,1.906 2.677,2.146 0.49,0.24 10 false USG1 2.313,1.438 2.729,1.688 0.417,0.25 10 false US1- 0.635,4.021 1.031,4.281 0.396,0.26 10 false UDO- 1.24,4.094 1.74,4.354 0.5,0.26 10 false UJSS 2.167,3.938 2.604,4.198 0.438,0.26 10 false UDO+ 1.583,0.271 2.042,0.469 0.458,0.198 10 false H100 1.625,2.26 1.938,2.458 0.313,0.198 10 false H15
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H100-2 (US1-) - H15-9 (UDO-) Always Below 1 Ω
H100-3 (US1+) - H15-10 (UDO+) Always Below 1 Ω
H100-5 (USG1) - H15-12 (UJSS) Always Below 1 Ω
H100-2 (US1-) or H15-9 (UDO-) - Body ground Always 10 kΩ or higher
H100-3 (US1+) or H15-10 (UDO+) - Body ground Always 10 kΩ or higher
H100-5 (USG1) or H15-12 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR