Home › General › MAINTENANCE › FRONT DISC BRAKE PAD › 2020.02–2020.11
RM37A0E _V1 General _086848 MAINTENANCE _0420825 FRONT DISC BRAKE PAD A

MAINTENANCE  FRONT DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)

·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-)auxiliary battery terminal. (for HV Model)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (for HV Model)

Hide 2.REMOVE FRONT WHEEL

Hide 3.REMOVE FRONT DISC BRAKE PAD

CAUTION:
·

Be careful not to get pinched by the front disc brake cylinder assembly or other parts when removing the front disc brake pads.

·
C423878

After lifting up the front disc brake cylinder assembly, secure it in place before performing any work on it.

·

The front disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C423879C01
2.083,3.021 2.281,3.198 0.198,0.177 10 true *a 0.667,2.76 0.979,2.917 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the front disc brake cylinder slide pin (lower side) and remove the bolt.

NOTICE:

Do not kink or damage the brake line.



b.

Pull the front disc brake cylinder assembly upward.


c.
C423880

Remove the 2 anti-squeal springs.


d.

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 04945 4.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

Remove the front No. 1 disc brake anti-squeal shim from each front disc brake pad.


b.
C423882

Using a screwdriver, remove the front disc brake pad wear indicator plate from each front disc brake pad.