Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.



CHECK FREEZE FRAME DATA WHEN DTC WAS STORED


HINT:
·

Freeze Frame Data is stored when a DTC is output.

·

Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3 and turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes
50001 435

d.

Select a DTC to display the Freeze Frame Data.


e.

Check the Freeze Frame Data for the output DTC.

Chassis > Brake/EPB
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
IG1 Voltage Value IG1 terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
BS1 Voltage Value +BS terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


Motor Power Supply Voltage BM terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal BM (which supplies power to the ABS motor) of the skid control ECU (brake actuator assembly)


FR Wheel Speed Front speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear skid control sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear skid control sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C
Max.: 175°C
Displays temperature master cylinder pressure sensor -
M/C Sensor Grade Master cylinder pressure sensor change (value detected by ECU) Min.: -30 MPa/s
Max.: 225 MPa/s
Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor (airbag sensor assembly) Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Steering Angle Value Steering sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0°
-
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to the ABS motor) from the skid control ECU (brake actuator assembly) to the ABS motor relay


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake actuator assembly) to the ABS solenoid relay


Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%
Max.: 127.5%
Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Power Train Driving force Powertrain drive torque Min.: -327680 N
Max.: 327670 N
- -
Gear Position Gear position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R Actual gear position -
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position -
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Brake Hold Control Mode Brake hold control mode Out of control mode /
Pressure hold mode /
Pressure release mode /
EPB lock mode
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated)
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated)
EPB lock mode: Parking brake is engaged during brake hold control
HINT:
·

EPB stands for electric parking brake

·

If the brake pedal is not depressed for 3 minutes or more after entering pressure hold mode, the system automatically changes to EPB lock mode



FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.105 m/s2
Max.: 24.908 m/s2
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During driving: Changes in proportion with vehicle acceleration/deceleration
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Travel Distance from IG ON Driving time after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Elapsed Time Time elapsed after ignition switch turned to ON Min.: 0.00 s
Max.: 100661.760 s
- -
MT2 Motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
- -
IG Switch Ignition switch ON status OFF / ON - -
Downhill Assist Control SW Downhill assist control switch OFF / ON - -
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed



Parking Brake SW Parking brake switch OFF / ON OFF: Parking brake released
ON: Parking brake applied
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake pedal support assembly) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Brake Hold Switch Brake hold switch (electric parking brake switch assembly) (PKB terminal input) OFF / ON OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON
HINT:

The brake hold switch (electric parking brake switch assembly) state is determined using the voltage at terminal PKB


Stop Light Relay Stop light control relay (stop light switch assembly) status
(STP terminal input)
OFF / ON OFF: Stop light control relay (stop light switch assembly) off and brake pedal released
ON: Stop light control relay (stop light switch assembly) on or brake pedal depressed
HINT:

The voltage of power supplied to the stop lights is measured at the STP terminal.


Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
HINT:

Refer to utility for details on how to enter Inspection Mode*1


TRC(TRAC) Control TRC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
HAB Control High power assist brake status OFF / ON OFF: During not control
ON: During control
-
Fail Status Brake booster failure status OFF / ON OFF: During not control
ON: During control
-
Fail Control Failure control status OFF / ON OFF: During not control
ON: During control
-
BA Ctrl Status BA control status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
w/ Pre-collision System
Stop Light Relay State for ECU Control Stop light control relay (stop light switch assembly) status (STPO terminal output) (for ECU control) OFF / ON OFF: Stop light control relay (stop light switch assembly) off (stop light off)
ON: Stop light control relay (stop light switch assembly) on (stop light on)
-
Solenoid State for ECU Control ABS solenoid relay status (for ECU control) OFF / ON OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating
-
Motor State for ECU Control ABS motor relay status (for ECU control) OFF / ON OFF: ABS motor relay not operating
ON: ABS motor relay operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion OFF / ON OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
-
Buzzer Meter buzzer OFF / ON OFF: Buzzer off
ON: Buzzer on
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

For details on Dealer Mode (Signal Check), refer to test mode procedure*2

·

For details on Dealer Mode (Calibration), refer to utility*3



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 35 km/h (22 mph) or more for approximately 1 second


TRC(TRAC)/VSC OFF SW VSC OFF switch (CSW terminal input) OFF / ON OFF: VSC OFF switch OFF
ON: VSC OFF switch ON
HINT:

The VSC OFF switch state is determined using the voltage at terminal CSW


FR Speed Open Front speed sensor RH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
FL Speed Open Front speed sensor LH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RR Speed Open Rear skid control sensor RH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RL Speed Open Rear skid control sensor LH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
EFI Communication Open ECM communication open detection Normal / Under intermittent Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected
-
Yaw Rate Open Yaw rate sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Deceleration Open Acceleration sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Steering Open Steering sensor open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Master Cylinder Open Master cylinder pressure sensor open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RR Speed Sensor Voltage Open Rear skid control sensor RH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RL Speed Sensor Voltage Open Rear skid control sensor LH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Normal / Under intermittent Normal: Noise not detected
Under intermittent: Noise detected
-
Brake Pedal Switch Open Brake pedal load sensing switch (brake pedal support assembly) open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Yaw Rate Sensor Voltage Open Yaw rate sensor (airbag sensor assembly) voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
EFI Communication Invalid ECM communication invalid detection Normal / Under intermittent Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Solenoid Power Supply Open Solenoid power supply voltage status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Motor Power Supply Open Motor power supply voltage status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Stop Switch Open Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Air Bag ECU Communication Open Airbag sensor assembly open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
FR Speed Signal Status Front wheel RH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
FL Speed Signal Status Front wheel LH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
RR Speed Signal Status Rear wheel RH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
RL Speed Signal Status Rear wheel LH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-



CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTC will also clear the Freeze Frame Data.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTC and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Brake/EPB > Clear DTCs
50002 435