DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Brake/EPB / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| IG1 Voltage Value | IG1 terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage |
| BS1 Voltage Value | +BS terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Motor Power Supply Voltage | BM terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| FR Wheel Speed | Front speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear skid control sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear skid control sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FR Wheel Acceleration | Front wheel RH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| FL Wheel Acceleration | Front wheel LH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| RR Wheel Acceleration | Rear wheel RH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| RL Wheel Acceleration | Rear wheel LH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa
Max.: 23.99 MPa |
Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| Zero Point of M/C | Memorized zero value | Min.: -12.5 MPa
Max.: 12.4 MPa |
- | - |
| Master Cylinder Sensor Temperature | Master cylinder pressure sensor temperature | Min.: -80°C
Max.: 175°C |
Displays temperature master cylinder pressure sensor | - |
| M/C Sensor Grade | Master cylinder pressure sensor change (value detected by ECU) | Min.: -30 MPa/s
Max.: 225 MPa/s |
Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Zero Point of Decele2 | Memorized zero value | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
- | - |
| Zero Point of Decele | Memorized zero value | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
- | - |
| Yaw Rate Sensor Value | Yaw rate sensor (airbag sensor assembly) | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Zero Point of Yaw Rate Sensor | Memorized zero value | Min.: -128°/s
Max.: 127°/s |
After completing zero point calibration: 0° | - |
| Zero Point of Yaw Rate Sensor2 | Memorized zero value | Min.: -128°/s
Max.: 127°/s |
After completing zero point calibration: 0° | - |
| Steering Angle Value | Steering angle sensor | Min.: -3276.8°
Max.: 3276.7° |
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0° |
- |
| Zero Point of Steering Angle | Memorized zero value | Min.: -3276.8°
Max.: 3276.7° |
- | - |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Power Train Driving force | Powertrain drive torque | Min.: -327680 N
Max.: 327670 N |
- | - |
| Gear Position | Gear position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R | Actual gear position | - |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode /
Pressure hold mode / Pressure release mode / EPB lock mode |
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed Grade | Vehicle acceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Vehicle Stop Time from IG ON | Time vehicle stopped after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Travel Distance from IG ON | Driving time after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Elapsed Time | Time elapsed after ignition switch turned to ON | Min.: 0.00 s
Max.: 100661.760 s |
- | - |
| MT2 | Motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
- | - |
| IG Switch | Ignition switch ON status | OFF / ON | - | - |
| Downhill Assist Control SW | Downhill assist control switch | OFF / ON | - | - |
| Stop Light SW | Stop light switch assembly status
(STP or STP2 terminal input) |
OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake switch | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch (brake pedal support assembly) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (PKB terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (stop light switch assembly) status
(STP terminal input) |
OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
|
| TRC(TRAC) Control | TRC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| HAB Control | High power assist brake status | OFF / ON | OFF: During not control
ON: During control |
- |
| Fail Status | Brake booster failure status | OFF / ON | OFF: During not control
ON: During control |
- |
| Fail Control | Failure control status | OFF / ON | OFF: During not control
ON: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
w/ Pre-collision System |
| Stop Light Relay State for ECU Control | Stop light control relay (stop light switch assembly) status (STPO terminal output) (for ECU control) | OFF / ON | OFF: Stop light control relay (stop light switch assembly) off (stop light off)
ON: Stop light control relay (stop light switch assembly) on (stop light on) |
- |
| Solenoid State for ECU Control | ABS solenoid relay status (for ECU control) | OFF / ON | OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating |
- |
| Motor State for ECU Control | ABS motor relay status (for ECU control) | OFF / ON | OFF: ABS motor relay not operating
ON: ABS motor relay operating |
- |
| Operation History of IG OFF while Vehicle is moving | History of ignition switch turned off when vehicle is in motion | OFF / ON | OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF
ON: VSC OFF switch ON |
|
| Brake Hold Ready | Brake hold control permission status | Not in stand-by mode / Stand-by mode | Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated) |
- |
| FR Speed Signal Status | Front wheel RH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| FL Speed Signal Status | Front wheel LH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| RR Speed Signal Status | Rear wheel RH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| RL Speed Signal Status | Rear wheel LH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| ABS Solenoid (SRLR) | Rear pressure reduction solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SRLH) | Rear pressure holding solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SRRR) | Rear pressure reduction solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SRRH) | Rear pressure holding solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SFLR) | Front pressure reduction solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SFLH) | Front pressure holding solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SFRR) | Front pressure reduction solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SFRH) | Front pressure holding solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| TRC(TRAC)/VSC Solenoid (SM2) | Master cylinder cut solenoid (Brake Pressure Control Solenoid "B") status | OFF / ON | OFF: Not operating
ON: Operating (pressure regulation) |
|
| TRC(TRAC)/VSC Solenoid (SM1) | Master cylinder cut solenoid (Brake Pressure Control Solenoid "A") status | OFF / ON | OFF: Not operating
ON: Operating (pressure regulation) |
|
| ABS Motor Relay | Motor relay | OFF / ON | OFF: Motor relay off
ON: Motor relay on |
- |
| Solenoid Relay | Solenoid relay | OFF / ON | OFF: Solenoid relay off
ON: Solenoid relay on |
- |
| STPO | Stop light control relay (stop light switch assembly) status (STPO terminal output) | OFF / ON | OFF: Stop light control relay (stop light switch assembly) off (Stop light off)
ON: Stop light control relay (stop light switch assembly) on (Stop light on) |
|
*1: for entering Inspection Mode:
*2: for performing Dealer Mode (Signal Check):
*3: for entering Dealer Mode (Calibration):
CHECK FOR INTERMITTENT PROBLEMS
A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected using the Data List function of the GTS.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Follow the directions on the GTS to display the Data List and select areas where momentary interruption should be monitored.
A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).
If Under intermittent remains displayed for one of the items on the GTS, check for continuity between the ECU and the item for which Under intermittent is displayed.
If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| FL Speed Open | Front speed sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RR Speed Open | Rear skid control sensor RH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RL Speed Open | Rear skid control sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| EFI Communication Open | ECM communication open detection | Normal / Under intermittent | Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected |
- |
| Yaw Rate Open | Yaw rate sensor (airbag sensor assembly) open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Deceleration Open | Acceleration sensor (airbag sensor assembly) open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Steering Open | Steering angle sensor open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RR Speed Sensor Voltage Open | Rear skid control sensor RH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RL Speed Sensor Voltage Open | Rear skid control sensor LH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| M/C Pressure Sensor Noise | Master cylinder pressure sensor noise detection | Normal / Under intermittent | Normal: Noise not detected
Under intermittent: Noise detected |
- |
| Brake Pedal Switch Open | Brake pedal load sensing switch (brake pedal support assembly) open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor (airbag sensor assembly) voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| EFI Communication Invalid | ECM communication invalid detection | Normal / Under intermittent | Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected |
- |
| Master Cylinder Pressure Sensor Power Supply Open | Master cylinder pressure sensor power supply voltage status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Solenoid Power Supply Open | Solenoid power supply voltage status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Motor Power Supply Open | Motor power supply voltage status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Stop Switch Open | Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Air Bag ECU Communication Open | Airbag sensor assembly open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
Select the line graph display.
Using the line graph, check whether the status is "Normal" or "Under intermittent".
Normal is displayed.
If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.
While observing the screen, gently jiggle the connector or wire harness between the ECU and each sensors, or between ECUs.
Normal is displayed.
If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.
If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Brake/EPB / Active Test.
According to the display on the GTS, perform the Active Test.
Although the Active Test automatically turns off the pump motor after approximately 5 seconds in order to protect the motor, do not operate the pump motor repeatedly without sufficient waiting time in between.
Although the Active Test automatically turns off each solenoid after approximately 2 seconds in order to protect the solenoid, do not operate the solenoids repeatedly without sufficient waiting time in between.
Do not depress the brake pedal when only the pressure release solenoids valves are ON.
| Tester Display | Measurement Item | Control Range | Restrict Condition | Diagnostic Note |
|---|---|---|---|---|
| EBS Relay | Emergency brake signal operation | Relay Start | Vehicle condition: Vehicle stopped
|
Whether the hazard warning lights blink when the EBS Relay is on can be confirmed. |
| ABS Solenoid | Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR) |
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P ·
Apply the parking brake
|
Refer to on-vehicle inspection for the brake actuator* |
| VSC Solenoid | Master cylinder cut solenoid (SMF (SM1), SMR (SM2)) | Solenoid Start (Activate)
Solenoid SMF / SMR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P ·
Apply the parking brake
|
Check that the GTS display for the solenoid (SM1 or SM2) changes to ON/OFF during Solenoid Start (Activate) |
| Motor Relay | ABS motor relay | OFF / ON | Vehicle condition: Vehicle stopped
|
Refer to on-vehicle inspection for the brake actuator* |
| Solenoid Relay | Solenoid relay | OFF / ON | Vehicle condition: Vehicle stopped
|
Perform the Active Test and check that the voltage displayed for the solenoid power supply voltage Data List item changes. |
| Stop Lamp Relay | Stop light control relay (Stop light switch assembly) | OFF / ON | Vehicle condition: Vehicle stopped
|
With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON |