Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

This DTC is stored when the skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the acceleration sensor (airbag sensor assembly).

This DTC may be stored due to an intermittent low power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range When the +BS terminal voltage is from 9.5 to 17.4 V at a vehicle speed exceeding 3 km/h (2 mph), an acceleration sensor (airbag sensor assembly) power source malfunction signal is received for 10 seconds or more.
·

Wire harness and connector

·

Acceleration sensor (airbag sensor assembly)



WIRING DIAGRAM

C400839E19
0.781,1.313 1.396,1.51 0.615,0.198 10 false CANL 6.104,1.333 6.719,1.531 0.615,0.198 10 false CANL 0.76,0.74 1.375,0.938 0.615,0.198 10 false CANH 6.083,0.719 6.698,0.917 0.615,0.198 10 false CANH 0.927,1.948 1.385,2.146 0.458,0.198 10 false IG2 2.01,2.104 2.906,2.292 0.896,0.188 10 false A/BAG-IG2 3.958,1.938 5.542,2.438 1.583,0.5 10 false from IG Circuit 1,2.573 1.313,2.771 0.313,0.198 10 false E1 1,3.177 1.313,3.375 0.313,0.198 10 false E2 0.094,3.896 2.333,4.344 2.24,0.448 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.104,3.74 0.563,3.938 0.458,0.198 10 false H58 2.823,4.375 4.781,4.802 1.958,0.427 10 false : CAN Communication Line 5.521,3.885 7.083,4.354 1.563,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.521,3.74 5.979,3.938 0.458,0.198 10 false A39 5.771,1.146 6.083,1.344 0.313,0.198 10 false 43 5.771,0.531 6.083,0.729 0.313,0.198 10 false 27 1.281,0.552 1.594,0.75 0.313,0.198 10 false 26 1.292,1.167 1.604,1.365 0.313,0.198 10 false 27 1.292,1.823 1.604,2.021 0.313,0.198 10 false 36 1.292,2.448 1.604,2.646 0.313,0.198 10 false 33 1.281,3.052 1.594,3.25 0.313,0.198 10 false 32 2.521,1.833 2.833,2.031 0.313,0.198 10 false 1 2.156,1.823 2.469,2.021 0.313,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
C379924C31
1.5,0.25 1.917,0.5 0.417,0.25 2.813,2.802 2.229,2.365 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.583,0.292 2.406,0.667 0.823,0.375 10 false H58 2.74,2.833 3.083,3.083 0.344,0.25 10 false IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the H58 yaw rate and acceleration sensor (airbag sensor assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H58-36 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (E1 AND E2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (E1 AND E2 TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H58-33 (E1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
H58-32 (E2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the H58 yaw rate and acceleration sensor (airbag sensor assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C14D71C is not output. A
DTC C14D71C is output. B



A

B