Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) U

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  TERMINALS OF ECU  


HYBRID VEHICLE CONTROL ECU


C338835E27
1.313,0.448 1.75,0.698 0.438,0.25 3.323,0.458 3.76,0.708 0.438,0.25 5.333,0.458 5.771,0.708 0.438,0.25 1.417,0.5 1.875,0.698 0.458,0.198 10 false A31 3.427,0.5 3.885,0.698 0.458,0.198 10 false A32 5.438,0.51 5.896,0.708 0.458,0.198 10 false H67

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
A31-2 (R) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in R 6.0 to 14 V
Ignition switch ON, shift lever not in R 0 to 1.5 V
A31-3 (DB1) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in D or S 6.0 to 14 V
Ignition switch ON, shift lever not in D or S 0 to 1.5 V
A31-4 (HMCH) - H67-3 (E1) Communication signal Ignition switch ON Pulse generation
(Waveform 1)
A31-5 (MREL) - H67-3 (E1) Main relay Ignition switch ON 11 to 14 V
A31-6 (HSDN) - H67-3 (E1) MG ECU shutdown signal Ignition switch ON (READY) 0 to 1.5 V
A31-7 (STP) - H67-3 (E1) Stop light switch Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V
A31-8 (LIN3) - H67-3 (E1) LIN communication signal
(A/C inverter, battery state sensor)
Ignition switch ON (READY) Pulse generation
A31-11 (+B1) - H67-3 (E1) Power source Ignition switch ON 11 to 14 V
A31-12 (OPM2) - H67-3 (E1) OIL PMP relay Ignition switch ON (READY), engine stopped 11 to 14 V
A31-14 (HMCL) - H67-3 (E1) Communication signal Ignition switch ON Pulse generation
(Waveform 1)
A31-15 (DB2) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in D or S 6.0 to 14 V
Ignition switch ON, shift lever not in D or S 0 to 1.5 V
A31-16 (PR) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in P or R 6.0 to 14 V
Ignition switch ON, shift lever not in P or R 0 to 1.5 V
A31-18 (PSFT) - H67-3 (E1) Shift lever position sensor power source Ignition switch ON (ACC) 6.0 to 14 V
A31-20 (BL) - H67-3 (E1) Back-up light relay Ignition switch ON, shift lever in R 11 to 14 V
A31-21 (OPM1) - H67-3 (E1) Oil pump with motor assembly signal Ignition switch ON (READY), engine stopped Pulse generation
(Waveform 2)
A31-22 (NOPM) - H67-3 (E1) Oil pump with motor assembly signal Ignition switch ON (READY), engine stopped Pulse generation
(Waveform 2)
A31-24 (VCPA) - A31-37 (EPA) Accelerator pedal sensor assembly power source (for VPA) Ignition switch ON 4.5 to 5.5 V
A31-26 (VCP2) - A31-25 (EPA2) Accelerator pedal sensor assembly power source (for VPA2) Ignition switch ON 4.5 to 5.5 V
A31-28 (P) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in P 6.0 to 14 V
Ignition switch ON, shift lever not in P 0 to 1.5 V
A31-29 (N) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in N 6.0 to 14 V
Ignition switch ON, shift lever not in N 0 to 1.5 V
A31-30 (PNB) - H67-3 (E1) Shift lever position signal Ignition switch ON, shift lever in P or N 6.0 to 14 V
A31-33 (NIWP) - H67-3 (E1) Inverter water pump assembly signal Ignition switch ON (READY) Pulse generation
(Waveform 3)
A31-34 (IWP) - H67-3 (E1) Inverter water pump assembly signal Ignition switch ON (READY) Pulse generation
(Waveform 3)
A31-36 (VPA) - A31-37 (EPA) Accelerator pedal sensor assembly (for accelerator pedal position detection) Ignition switch ON, accelerator pedal released 0.4 to 1.4 V
Ignition switch ON, engine stopped, shift lever in P, accelerator pedal fully depressed 2.6 to 4.5 V
A31-38 (VPA2) - A31-25 (EPA2) Accelerator pedal sensor assembly (for accelerator pedal sensor malfunction detection) Ignition switch ON, accelerator pedal released 1.0 to 2.2 V
Ignition switch ON, engine stopped, shift lever in P, accelerator pedal fully depressed 3.4 to 5.3 V
A31-40 (TTA) - A31-39 (ETTA) Transmission fluid temperature sensor Ignition switch ON, temperature 25°C (77°F) 3.6 to 4.6 V
Ignition switch ON, temperature 60°C (140°F) 2.2 to 3.2 V
A31-46 (MMT) - A31-45 (MMTG) Motor temperature sensor Ignition switch ON, temperature 25°C (77°F) 3.6 to 4.6 V
Ignition switch ON, temperature 60°C (140°F) 2.2 to 3.2 V
A31-48 (GMT) - A31-47 (GMTG) Generator temperature sensor Ignition switch ON, temperature 25°C (77°F) 3.6 to 4.6 V
Ignition switch ON, temperature 60°C (140°F) 2.2 to 3.2 V
A32-5 (ILK) - H67-3 (E1) Interlock switch Ignition switch ON, service plug grip installed correctly 0 to 1.5 V
Ignition switch ON, service plug grip not installed 11 to 14 V
A32-7 (CA3P) - H67-3 (E1) CAN communication signal Ignition switch ON Pulse generation
(Waveform 4)
A32-8 (CA1L) - H67-3 (E1) CAN communication signal Ignition switch ON Pulse generation
(Waveform 5)
A32-9 (CA4H) - H67-3 (E1) CAN communication signal Ignition switch ON Pulse generation
(Waveform 6)
A32-13 (SMRG) - A32-12 (E01) System main relay operation signal Ignition switch ON → Ignition switch ON (READY) Pulse generation
(Waveform 7)
A32-15 (SMRP) - A32-12 (E01) System main relay operation signal Ignition switch ON → Ignition switch ON (READY) Pulse generation
(Waveform 7)
A32-16 (SMRB) - A32-12 (E01) System main relay operation signal Ignition switch ON → Ignition switch ON (READY) Pulse generation
(Waveform 7)
A32-20 (CA3N) - H67-3 (E1) CAN communication signal Ignition switch ON Pulse generation
(Waveform 4)
A32-21 (CA1H) - H67-3 (E1) CAN communication signal Ignition switch ON Pulse generation
(Waveform 5)
A32-22 (CA4L) - H67-3 (E1) CAN communication signal Ignition switch ON Pulse generation
(Waveform 6)
A32-25 (PLKC) - H67-3 (E1) Shift lock release request signal Ignition switch ON (READY), brake pedal depressed 11 to 14 V
Ignition switch ON (READY), brake pedal released 0 to 1.5 V
A32-28 (ST1-) - H67-3 (E1) Stop light switch signal Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 11 to 14 V
A32-29 (ACCI) - H67-3 (E1) ACC relay Ignition switch ON (ACC) 11 to 14 V
A32-35 (IG2) - H67-3 (E1) Power source Ignition switch ON 11 to 14 V
H67-1 (+B2) - H67-3 (E1) Power source Ignition switch ON 11 to 14 V
H67-4 (ST2) - H67-3 (E1) Starter signal Ignition switch ON 0 to 1.5 V
H67-7 (INDR) - H67-3 (E1) Shift position indicator signal Ignition switch ON, shift lever in R 0 to 3.2 V
Ignition switch ON, shift lever not in R 11 to 14 V
H67-8 (INDD) - H67-3 (E1) Shift position indicator signal Ignition switch ON, shift lever in D 0 to 3.2 V
Ignition switch ON, shift lever not in D 11 to 14 V
H67-11 (SFTD) - H67-3 (E1) Transmission control Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever in (-) 0 to 1.5 V
H67-19 (INDP) - H67-3 (E1) Shift position indicator signal Ignition switch ON, shift lever in P 0 to 3.2 V
Ignition switch ON, shift lever not in P 11 to 14 V
H67-20 (INDM) - H67-3 (E1) Shift position indicator signal Ignition switch ON, shift lever in S 0 to 3.2 V
Ignition switch ON, shift lever not in S 11 to 14 V
H67-21 (INDN) - H67-3 (E1) Shift position indicator signal Ignition switch ON, shift lever in N 0 to 3.2 V
Ignition switch ON, shift lever not in N 11 to 14 V
H67-24 (SFTU) - H67-3 (E1) Transmission control Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever in (+) 0 to 1.5 V
H67-25 (M) - H67-3 (E1) Transmission control Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever not in S 0 to 1.5 V
H67-27 (BATT) - H67-3 (E1) Constant power source Ignition switch ON 11 to 14 V
Ignition switch ON (READY) 11 to 15.5 V
H67-33 (EVSW) - H67-3 (E1) EV drive mode switch (pattern select switch assembly) Ignition switch ON, EV drive mode switch (pattern select switch assembly) not operated 11 to 14 V
Ignition switch ON, EV drive mode switch (pattern select switch assembly) being pushed and held 0 to 1.5 V
H67-37 (DMS-) - H67-3 (E1) Drive mode select switch (No. 1 pattern select switch assembly) signal Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) not turned 11 to 14 V
Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) backward and held 0 to 1.5 V
H67-38 (DMS+) - H67-3 (E1) Drive mode select switch (No. 1 pattern select switch assembly) signal Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) not turned 11 to 14 V
Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) forward and held 0 to 1.5 V
H67-44 (IGB) - H67-3 (E1) Power source Ignition switch ON 11 to 14 V

a.

Oscilloscope waveforms

HINT:

Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


i.
A284438E08
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 1 (Communication signal)

Item Content
Terminal CH1: A31-4 (HMCH) - H67-3 (E1)
CH2: A31-14 (HMCL) - H67-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



ii.
C206009E04
2.972,0.79 3.304,0.983 0.332,0.193 10 GND 2.972,1.376 3.304,1.569 0.332,0.193 10 GND 0.204,0.651 0.536,0.844 0.332,0.193 10 CH1 0.204,1.265 0.536,1.459 0.332,0.193 10 CH2

Waveform 2 (Oil pump with motor assembly signal)

Item Content
Terminal CH1: A31-21 (OPM1) - H67-3 (E1)
CH2: A31-22 (NOPM) - H67-3 (E1)
Equipment Setting 10 V/DIV., 20 ms./DIV.
Condition Ignition switch ON (READY), engine stopped

HINT:

The wavelength will vary with the operating speed of the oil pump.



iii.
A415999E04
0.365,0.854 0.823,1.052 0.458,0.198 10 false CH1 0.375,1.417 0.833,1.615 0.458,0.198 10 false CH2 2.958,1.635 3.281,1.917 0.323,0.281 10 false GND 2.958,0.854 3.281,1.135 0.323,0.281 10 false GND

Waveform 3 (Inverter water pump assembly signal)

Item Content
Terminal CH1: A31-34 (IWP) - H67-3 (E1)
CH2: A31-33 (NIWP) - H67-3 (E1)
Equipment Setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON (READY)

HINT:

The duty of the IWP signal and the frequency of the NIWP signal change according to the coolant (for inverter) temperature.



iv.
A284438E10
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 4 (CAN communication signal)

Item Content
Terminal CH1: A32-7 (CA3P) - H67-3 (E1)
CH2: A32-20 (CA3N) - H67-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



v.
A284438E09
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 5 (CAN communication signal)

Item Content
Terminal CH1: A32-21 (CA1H) - H67-3 (E1)
CH2: A32-8 (CA1L) - H67-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



vi.
A284438E09
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 6 (CAN Communication signal)

Item Content
Terminal CH1: A32-9 (CA4H) - H67-3 (E1)
CH2: A32-22 (CA4L) - H67-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



vii.
C206010E19
2.958,0.656 3.292,0.896 0.333,0.24 10 false GND 2.958,1.042 3.292,1.281 0.333,0.24 10 false GND 2.958,1.427 3.292,1.667 0.333,0.24 10 false GND 0.271,0.573 0.594,0.781 0.323,0.208 10 false CH1 0.281,0.948 0.615,1.188 0.333,0.24 10 false CH2 0.292,1.313 0.625,1.552 0.333,0.24 10 false CH3

Waveform 7 (System main relay operation signal)

Item Content
Terminal CH1: A32-15 (SMRP) - A32-12 (E01)
CH2: A32-16 (SMRB) - A32-12 (E01)
CH3: A32-13 (SMRG) - A32-12 (E01)
Equipment Setting 10 V/DIV., 200 ms./DIV.
Condition Ignition switch ON → Ignition switch ON (READY)




BATTERY VOLTAGE SENSOR


A449749E01
1.646,3.156 2.073,3.385 0.427,0.229 4.781,3.146 5.208,3.375 0.427,0.229 6.094,3.146 6.521,3.375 0.427,0.229 1.76,3.188 2.073,3.385 0.313,0.198 10 false z15 4.896,3.188 5.208,3.385 0.313,0.198 10 false z12 6.24,3.167 6.552,3.365 0.313,0.198 10 false y1

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
z12-1 (TC0) - z12-13 (GC0) HV battery intake air temperature sensor Ignition switch ON, HV battery intake air temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-2 (TB5) - z12-14 (GB5) Battery temperature sensor 5 Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-3 (TB4) - z12-15 (GB4) Battery temperature sensor 4 Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-4 (TB3) - z12-16 (GB3) Battery temperature sensor 3 Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-5 (TB2) - z12-17 (GB2) Battery temperature sensor 2 Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-6 (TB1) - z12-18 (GB1) Battery temperature sensor 1 Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-7 (TB0) - z12-19 (GB0) Battery temperature sensor 0 Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-9 (IB0) - z12-22 (GIB) Battery current sensor Ignition switch ON 0.5 to 4.5 V
z12-10 (VIB) - z12-22 (GIB) Power source for battery current sensor Ignition switch ON 4.5 to 5.5 V
y1-1 (IGCT) - y1-7 (GND) Control signal Ignition switch ON 11 to 14 V
y1-2 (CA1H) - y1-7 (GND) CAN communication signal Ignition switch ON Pulse generation
(waveform 1)
y1-3 (CA1L) - y1-7 (GND) CAN communication signal Ignition switch ON Pulse generation
(waveform 1)
y1-5 (SI0) - y1-7 (GND) Battery cooling blower (No. 0) operation signal Cooling blower operating Pulse generation
(Waveform 2)
Cooling blower not operating 4.5 to 5.5 V
y1-6 (SI1) - y1-7 (GND) Battery cooling blower (No. 1) operation signal Cooling blower operating Pulse generation
(Waveform 3)
Cooling blower not operating 4.5 to 5.5 V
y1-7 (GND) - Body ground Ground Always (continuity check) Below 1 Ω
y1-11 (FP0) - y1-7 (GND) Battery cooling blower (No. 0) monitor signal Cooling blower not operating 0 Hz
Cooling blower operating Pulse generation
(waveform 4)
y1-12 (FP1) - y1-7 (GND) Battery cooling blower (No. 1) monitor signal Cooling blower not operating 0 Hz
Cooling blower operating Pulse generation
(waveform 5)

a.

Oscilloscope waveforms

HINT:

Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


i.
A284438E09
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 1 CAN communication signal)

Item Content
Terminal CH1: y1-2 (CA1H) - y1-7 (GND)
CH2: y1-3 (CA1L) - y1-7 (GND)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



ii.
C257882E03
2.99,1.052 3.396,1.292 0.406,0.24 10 false GND

Waveform 2 (Battery cooling blower (No. 0) operation signal)

Item Content
Terminal y1-5 (SI0) - y1-7 (GND)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Battery cooling blower assembly operating (Active Test of cooling fan being performed)

HINT:

The waveform will vary with the operating speed of the battery cooling blower assembly.



iii.
C257882E03
2.99,1.052 3.396,1.292 0.406,0.24 10 false GND

Waveform 3 (Battery cooling blower (No. 1) operation signal)

Item Content
Terminal y1-6 (SI1) - y1-7 (GND)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Battery cooling blower assembly operating (Active Test of cooling fan being performed)

HINT:

The waveform will vary with the operating speed of the battery cooling blower assembly.



iv.
A284436E07
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND

Waveform 4 (Battery cooling blower (No. 0) monitor signal)

Item Content
Terminal y1-11 (FP0) - y1-7 (GND)
Equipment Setting 2 V/DIV., 2 ms/DIV.
Condition Battery cooling blower assembly operating (Active Test of cooling fan being performed)

HINT:

The frequency of the waveform will vary with the operating speed of the battery cooling blower assembly.



v.
A284436E07
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND

Waveform 5 (Battery cooling blower (No. 1) monitor signal)

Item Content
Terminal y1-12 (FP1) - y1-7 (GND)
Equipment Setting 2 V/DIV., 2 ms/DIV.
Condition Battery cooling blower assembly operating (Active Test of cooling fan being performed)

HINT:

The frequency of the waveform will vary with the operating speed of the battery cooling blower assembly.