CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the No. 1 skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A44-1 (MRI1) - Body ground | Brake booster with accumulator pump assembly power supply input | Always | 11 to 14 V |
| A44-2 (MGND) - Body ground | Brake booster with accumulator pump assembly ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A44-3 (SKS1) | Brake pedal stroke sensor 1 signal input | - | - |
| A44-4 | - | - | - |
| A44-5 | - | - | - |
| A44-6 | - | - | - |
| A44-7 | - | - | - |
| A44-8 | - | - | - |
| A44-9 | - | - | - |
| A44-10 | - | - | - |
| A44-11 | - | - | - |
| A44-12 (LBL) | Brake fluid level warning switch (Brake master cylinder reservoir assembly) input | - | - |
| A44-13 | - | - | - |
| A44-14 (+BI1) - Body ground | +BI1 power source input | Always | 11 to 14 V |
| A44-15 (BS) - Body ground | Solenoid power supply input | Always | 11 to 14 V |
| A44-16 (VSK1) | Brake pedal stroke sensor 1 power supply output | - | - |
| A44-17 | - | - | - |
| A44-18 (SKG1) | Brake pedal stroke sensor 1 ground | - | - |
| A44-19 | - | - | - |
| A44-20 | - | - | - |
| A44-21 | - | - | - |
| A44-22 | - | - | - |
| A44-23 | - | - | - |
| A44-24 | - | - | - |
| A44-25 (CSW2) | No. 2 skid control ECU (brake actuator assembly) operation signal output | - | - |
| A44-26 | - | - | - |
| A44-27 | - | - | - |
| A44-28 (GND1) - Body ground | No. 1 skid control ECU (Brake booster with master cylinder assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A44-29 (M+) | Brake booster with accumulator pump assembly power supply (+) | - | - |
| A44-30 (M-) | Brake booster with accumulator pump assembly power supply (-) | - | - |
| A44-31 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V |
| A44-32 | - | - | - |
| A44-33 | - | - | - |
| A44-34 | - | - | - |
| A44-35 (CA2H) | CAN communication line 2 (H) | - | - |
| A44-36 (CA2L) | CAN communication line 2 (L) | - | - |
| A44-37 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A44-38 (CA1H) | CAN communication line 1 (H) | - | - |
| A44-39 (CA1L) | CAN communication line 1 (L) | - | - |
| A44-40 (CTY) - Body ground | Front door courtesy light switch assembly input (for driver side) | Driver door closed → open | 11 to 14 V → Below 1.5 V |
| A44-41 | - | - | - |
| A44-42 (IG2) - Body ground | IG2 power source input | Ignition switch ON | 11 to 14 V |
CHECK BRAKE ACTUATOR ASSEMBLY
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to No. 2 Skid Control ECU (brake actuator assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the No. 2 skid control ECU (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A57-1 (GND1) - Body ground | No. 2 skid control ECU (brake actuator assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A57-2 | - | - | - |
| A57-3 | - | - | - |
| A57-4 (RL-) | Rear speed sensor LH (-) signal input | - | - |
| A57-5 (RL+) | Rear speed sensor LH (+) power supply output | - | - |
| A57-6 (FR-) | Front speed sensor RH (-) signal input | - | - |
| A57-7 (FR+) | Front speed sensor RH (+) power supply output | - | - |
| A57-8 | - | - | - |
| A57-9 (CSW) - Body ground | VSC OFF switch input | VSC OFF switch is pushed → released | Below 1 Ω → 10 kΩ or higher |
| A57-10 (SKS2) | Brake pedal stroke sensor 2 signal input | - | - |
| A57-11 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A57-12 | - | - | - |
| A57-13 | - | - | - |
| A57-14 (+BS) - Body ground | ABS solenoid relay power supply input | Always | 11 to 14 V |
| A57-15 (IG2) - Body ground | IG2 power source input | Ignition switch ON | 11 to 14 V |
| A57-16 (CA2H) | CAN communication line 2 (H) | - | - |
| A57-17 (CA2L) | CAN communication line 2 (L) | - | - |
| A57-18 (SP1) | Speed sensor signal output | - | - |
| A57-19 (RR-) | Rear speed sensor RH (-) signal input | - | - |
| A57-20 (RR+) | Rear speed sensor RH (+) power supply output | - | - |
| A57-21 (FL-) | Front speed sensor LH (-) signal input | - | - |
| A57-22 (FL+) | Front speed sensor LH (+) power supply output | - | - |
| A57-23 | - | - | - |
| A57-24 | - | - | - |
| A57-25 (VSK2) | Brake pedal stroke sensor 2 power supply output | - | - |
| A57-26 (SKG2) | Brake pedal stroke sensor 2 ground | - | - |
| A57-27 (CANH) | CAN communication line (H) | - | - |
| A57-28 | - | - | - |
| A57-29 (CTY) - Body ground | No. 2 Skid control ECU (brake actuator assembly) operation signal input | Ignition switch ON | 11 to 14 V |
| A57-30 (GND2) - Body ground | ABS motor ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A57-31 | - | - | - |
| A57-32 (STPO) - Body ground | Stop light control relay (Stop light switch assembly) output | Always | 11 to 14 V |
| A57-33 | - | - | - |
| A57-34 | - | - | - |
| A57-35 (PKB) - Body ground | Brake hold switch (Electric parking brake switch assembly) input | Brake hold switch (electric parking brake switch assembly) is pushed → released | Below 1 Ω → 10 kΩ or higher |
| A57-36 | - | - | - |
| A57-37 (STP2) - Body ground | Stop light control relay (Stop light switch assembly) input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A57-38 | - | - | - |
| A57-39 | - | - | - |
| A57-40 | - | - | - |
| A57-41 | - | - | - |
| A57-42 | - | - | - |
| A57-43 (CANL) | CAN communication line (L) | - | - |
| A57-44 | - | - | - |
| A57-45 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V |
| A57-46 (BM) - Body ground | ABS motor relay power supply input | Always | 11 to 14 V |