Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  U007488  Control Module Communication Bus "B" Off Bus Off  U010087  Lost Communication with ECM/PCM "A" Missing Message  U010187  Lost Communication with TCM Missing Message  U011087  Lost Communication with Drive Motor Control Module "A" Missing Message  U012587  Lost Communication with Multi-axis Acceleration Sensor Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  U015187  Lost Communication with Restraints Control Module Missing Message  U025E87  Lost Communication with Electronic Brake Booster Control Module "A" Missing Message  U029387  Lost Communication with Hybrid/EV Powertrain Control Module Missing Message  U110787  Lost Communication with Power Management Module Missing Message  U111A87  Lost Communication with ECM/PCM "A" (ch2) Missing Message  U115087  Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message  U115987  Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message  


DESCRIPTION

The yaw rate sensor has a built-in acceleration sensor.

The No. 2 skid control ECU (brake actuator assembly) receives signals from the hybrid vehicle control ECU, steering angle sensor, certification ECU (smart key ECU assembly), inverter with converter assembly, No. 1 skid control ECU (brake booster with master cylinder assembly), airbag sensor assembly, yaw rate sensor and ECM via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U007488 Control Module Communication Bus "B" Off Bus Off When the +BS terminal voltage is between 9.5 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 60 seconds or more. CAN communication line Output ECU: No. 2 skid control ECU (brake actuator assembly)
U010087 Lost Communication with ECM/PCM "A" Missing Message When terminal IG2 voltage is 10 V or more, data cannot be received from the ECM for 2 seconds or more.
·

CAN communication line

·

ECM

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U010187 Lost Communication with TCM Missing Message When terminal IG2 voltage is 10 V or more, data cannot be received from the hybrid vehicle control ECU for 2 seconds or more.
·

CAN communication line

·

Hybrid vehicle control ECU

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U011087 Lost Communication with Drive Motor Control Module "A" Missing Message When terminal IG2 voltage is 10 V or more, data from the inverter with converter assembly cannot be received for 2 seconds or more.
·

CAN communication line

·

Inverter with converter assembly

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Either of the following is detected:
·

When the +BS terminal voltage is between 9.5 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more.

·

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds:

-

Data from the acceleration sensor cannot be received once or more within 5 seconds.



·

CAN communication line

·

Acceleration sensor (yaw rate sensor)

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Either of the following is detected:
·

When the +BS terminal voltage is between 9.5 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.

·

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds:

-

Data from the steering angle sensor cannot be received once or more within 5 seconds



·

CAN communication line

·

Steering angle sensor

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U015187 Lost Communication with Restraints Control Module Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 7 km/h (4 mph), data cannot be received from the airbag sensor assembly for 5 seconds or more.
·

CAN communication line

·

Airbag sensor assembly

·

No. 2 skid control ECU (brake actuator assembly)


·

Output ECU: No. 2 skid control ECU (brake actuator assembly)

·

w/ Pre-collision System


U025E87 Lost Communication with Electronic Brake Booster Control Module "A" Missing Message When the voltage at terminal IG1 is 10 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more.
·

CAN communication line

·

No. 1 skid control ECU (brake booster with master cylinder assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message When terminal IG2 voltage is 10 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more.
·

CAN communication line

·

Hybrid vehicle control ECU

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U110787 Lost Communication with Power Management Module Missing Message When the voltage at terminal IG1 is 10 V or more, the certification ECU (smart key ECU assembly) cannot communicate for 3 seconds or more.
·

CAN communication line

·

Certification ECU (smart key ECU assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U111A87 Lost Communication with ECM/PCM "A" (ch2) Missing Message When terminal IG2 voltage is 10 V or more, data cannot be received from the ECM for 2 seconds or more.
·

CAN communication line

·

ECM

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U115087 Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message When terminal IG2 voltage is 10 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more.
·

CAN communication line

·

Hybrid vehicle control ECU

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
U115987 Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message When the voltage at terminal IG1 is 10 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more.
·

CAN communication line

·

No. 1 skid control ECU (brake booster with master cylinder assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

PROCEDURE

1.CHECK DTC (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


Result:
Result Proceed to

*: w/ Pre-collision System

DTCs for related systems are output together with U007488, U010087, U010187, U011087, U012587, U012687, U015187*, U025E87, U029387, U110787, U111A87, U115087 or U115987. A
DTC U007488, U010087, U010187, U011087, U012587, U012687, U015187*, U025E87, U029387, U110787, U111A87, U115087 or U115987 is output. B
DTCs are not output. C



A

GO TO DIAGNOSTIC TROUBLE CODE CHART (RELATED SYSTEM)

B

C