Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for A25A-FXS)
RM37A0E _52 Drivetrain _086862 DRIVE SHAFT / PROPELLER SHAFT _0421212 FRONT DRIVE SHAFT ASSEMBLY(for A25A-FXS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for A25A-FXS)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


c.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



d.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

115 to 135 g (4.06 to 4.76 oz)



e.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447E 2.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle outboard joint boot clamp to the front axle outboard joint boot.


c.
C298538C01
2.219,1.26 2.74,1.26 true 2.792,1.177 3.25,1.375 0.458,0.198 10 false SST 2.448,1.719 2.76,1.917 0.313,0.198 10 false *a 1.542,0.125 1.854,0.323 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST to the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C164317N01
1.781,1.5 2.531,1.5 false 2.573,1.417 3.031,1.615 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0472 to 0.1575 in.)


If the clearance is not as specified, retighten SST.


Hide 43447F 3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.


c.
C285537C04
0.708,0.646 1.469,1.021 false 2.656,0.594 2.969,0.792 0.313,0.198 10 false *a 1.219,0.292 1.531,0.49 0.313,0.198 10 false *b 0.427,0.552 0.885,0.75 0.458,0.198 10 false SST
*a Turn
*b Hold


Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C106165N13
2.031,1.031 2.698,1.844 false 2.646,1.865 3.094,2.104 0.448,0.24 10 SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0472 to 0.1575 in.)


If the clearance is not as specified, retighten SST.


Hide 43474E 4.INSTALL FRONT DRIVE SHAFT DAMPER

a.
C319690C06
0.719,1.688 0.719,1.375 false 0.208,1.677 0.208,1.323 false 1.406,1.677 1.406,1.323 false 1.344,1.698 1.656,1.854 0.313,0.156 10 false *1 0.667,1.708 0.979,1.865 0.313,0.156 10 false *2 1.802,0.313 1.958,0.51 0.156,0.198 10 false A 0.146,1.708 0.458,1.865 0.313,0.156 10 false *1
*1 Front Drive Shaft Damper Clamp
*2 Front Drive Shaft Damper


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.


b.

Set the dimension (A) as specified below.

Dimension (A):
for LH Side 240.7 to 244.7 mm (9.48 to 9.63 in.)
for RH Side 242.7 to 246.7 mm (9.56 to 9.71 in.)



Hide 43474F 5.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C292475

Using needle-nose pliers, install the 2 front drive shaft damper clamps as shown in the illustration.

NOTICE:
·

Be sure to install the clamps in the correct position.

·

Do not damage the front drive shaft damper.




Hide 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C067417C02
1.26,1.719 2.125,1.719 2.125,1.719 1.76,1.427 false 2.156,1.625 2.542,1.885 0.385,0.26 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




f.
C426391

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:

220 to 240 g (7.76 to 8.47 oz)



h.
C374772C01
1.74,0.896 1.198,0.292 1.198,0.292 2.042,0.521 false 1,0.167 1.313,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C375254C05
0.271,0.333 0.646,0.573 0.375,0.24 10 false *A 0.146,1.635 0.521,1.875 0.375,0.24 10 false *B 1.448,1.188 1.677,1.5 0.229,0.313 10 false A 1.49,2.531 1.719,2.844 0.229,0.313 10 false A
*A for LH Side
*B for RH Side


Check whether the dimension (A) of each drive shaft is within the specification.

NOTICE:

Keep the drive shaft assembly level during inspection.


Dimension (A):
for LH Side 621.1 mm (2.04 ft.)
for RH Side 946.5 mm (3.10 ft.)



Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot.


c.
C296175C02
1.74,1.396 2.104,1.708 2.104,1.708 2.729,1.708 true 2.781,1.625 3.24,1.823 0.458,0.198 10 false SST 2.729,0.094 3.042,0.292 0.313,0.198 10 false *a 1.448,0.521 1.76,0.719 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C195760N02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0472 to 0.1575 in.)


If the clearance is not as specified, retighten SST.


Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.


c.
C298539C02
0.677,1.625 1.521,1.625 1.521,1.625 2.146,1.125 true 0.385,1.542 0.844,1.74 0.458,0.198 10 false SST 2.281,1.76 2.594,1.958 0.313,0.198 10 false *a 1.938,0.073 2.25,0.271 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C086270N05
0.708,1.333 1.125,1.333 1.125,1.333 1.656,0.885 true 0.406,1.25 0.865,1.448 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0472 to 0.1575 in.)


If the clearance is not as specified, retighten SST.