Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2GR-FKS) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086862 DRIVE SHAFT / PROPELLER SHAFT _0421213 FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C108564

Using pliers, separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C374772C01
1.74,0.896 1.198,0.292 1.198,0.292 2.042,0.521 false 1,0.167 1.313,0.365 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C426391

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


f.
C141145C04
2.844,1.031 1.813,1.479 1.813,1.479 2.896,1.104 false 1.625,1.396 1.896,1.646 0.271,0.25 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474F 6.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C292475

Using needle-nose pliers, separate the 2 front drive shaft damper clamps.


Hide 43474E 7.REMOVE FRONT DRIVE SHAFT DAMPER

a.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43447F 8.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C081167

Using pliers, separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.


Hide 43447E 9.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the outboard joint.


Hide 41336D 11.REMOVE FRONT DRIVE SHAFT DUST COVER RH (for RH Side)

a.
F040647N02
1.927,0.813 2.313,0.354 2.313,0.354 2.542,0.354 false 2.583,0.292 2.979,0.521 0.396,0.229 10 false SST

Using SST and a press, remove the front drive shaft dust cover RH.

SST
09950-00020  

NOTICE:
·

Do not drop the front drive inboard joint assembly.

·

Do not overtighten SST.




Hide 43410C 12.REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

a.
C127665

Using a snap ring expander, remove the drive shaft hole snap ring.


b.
C127666N09
2.083,1.208 2.792,0.979 2.792,0.979 2.458,1.51 false 2.854,0.906 3.313,1.104 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft bearing.

SST
09527-10011  

NOTICE:

Do not drop the front drive inboard joint assembly.