Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
43410C
1.INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)
| *a | Steel Plate |
Using SST, a steel plate and a press, install a new front drive shaft bearing.
The bearing should be completely installed.
Using a snap ring expander, install a new drive shaft hole snap ring.
Install the drive shaft hole snap ring securely.
41336D
2.INSTALL FRONT DRIVE SHAFT DUST COVER RH (for RH Side)
| *a | Steel Plate |
Using a steel plate and a press, install a new front drive shaft dust cover RH until the dimension (A) from the tip of the front drive inboard joint assembly to the front drive shaft dust cover RH meets the specification.
341.7 to 342.3 mm (13.45 to 13.48 in.)
Be careful not to damage the front drive shaft dust cover RH.
3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
| *a | Protective Tape |
Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.
| *1 | Front Drive Outboard Joint Shaft Assembly |
| *2 | Front No. 2 Axle Outboard Joint Boot Clamp |
| *3 | Front Axle Outboard Joint Boot |
| *4 | Front Axle Outboard Joint Boot Clamp |
|
Outboard Joint Side |
|
Inboard Joint Side |
Install new parts to the front drive outboard joint shaft assembly in the following order:
Front No. 2 axle outboard joint boot clamp
Front axle outboard joint boot
Front axle outboard joint boot clamp
Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.
115 to 135 g (4.06 to 4.76 oz)
Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.
Do not allow grease to adhere to the boot clamp track of the outboard joint boot.
Keep the inside of the outboard joint boot free of foreign matter.
43447E
4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the front axle outboard joint boot clamp to the front axle outboard joint boot.
| *a | Turn |
| *b | Hold |
Place SST to the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front axle outboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front axle outboard joint boot clamp.
1.2 to 4.0 mm (0.0472 to 0.1575 in.)
If the clearance is not as specified, retighten SST.
43447F
5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.
| *a | Turn |
| *b | Hold |
Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.
1.2 to 4.0 mm (0.0472 to 0.1575 in.)
If the clearance is not as specified, retighten SST.
43474E
6.INSTALL FRONT DRIVE SHAFT DAMPER
| *1 | Front Drive Shaft Damper Clamp |
| *2 | Front Drive Shaft Damper |
Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.
Set the dimension (A) as specified below.
| for LH Side | 240.7 to 244.7 mm (9.48 to 9.63 in.) |
| for RH Side | 242.7 to 246.7 mm (9.56 to 9.71 in.) |
43474F
7.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Using needle-nose pliers, install the 2 front drive shaft damper clamps as shown in the illustration.
Be sure to install the clamps in the correct position.
Do not damage the front drive shaft damper.
8.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
| *1 | Front Axle Inboard Joint Boot Clamp |
| *2 | Front Axle Inboard Joint Boot |
| *3 | Front No. 2 Axle Inboard Joint Boot Clamp |
| *a | Protective Tape |
|
Outboard Joint Side |
|
Inboard Joint Side |
Install new parts to the front drive outboard joint shaft assembly in the following order:
Front axle inboard joint boot clamp
Front axle inboard joint boot
Front No. 2 axle inboard joint boot clamp
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Remove the protective tape.
| *a | Matchmark |
Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.
Face the serrated side of the tripod joint outward and install it to the outboard joint end.
Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.
Do not tap the rollers.
Keep the tripod joint free of foreign matter.
Be sure to install the tripod joint in the correct direction.
Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.
Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.
220 to 240 g (7.76 to 8.47 oz)
| *a | Matchmark |
Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.
9.INSTALL FRONT AXLE INBOARD JOINT BOOT
Install the front axle inboard joint boot to the front drive inboard joint assembly.
| *A | for LH Side |
| *B | for RH Side |
Check whether the dimension (A) of each drive shaft is within the specification.
Keep the drive shaft assembly level during inspection.
| for LH Side | 621.1 mm (2.04 ft.) |
| for RH Side | 949 mm (3.11 ft.) |
43448F
10.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the front axle inboard joint boot clamp to the front axle inboard joint boot.
| *a | Turn |
| *b | Hold |
Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front axle inboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front axle inboard joint boot clamp.
1.2 to 4.0 mm (0.0472 to 0.1575 in.)
If the clearance is not as specified, retighten SST.
43448G
11.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
Secure the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.
| *a | Turn |
| *b | Hold |
Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.
1.2 to 4.0 mm (0.0472 to 0.1575 in.)
If the clearance is not as specified, retighten SST.
12.INSPECT FRONT DRIVE SHAFT ASSEMBLY