Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY (for A25A-FXS, A25B-FXS)
RM37A0E _52 Drivetrain _086862 DRIVE SHAFT / PROPELLER SHAFT _0421214 REAR DRIVE SHAFT ASSEMBLY(for A25A-FXS) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for A25A-FXS)  DISASSEMBLY  


PROCEDURE

Hide 42347F 1.SEPARATE REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C429354

Using pliers, separate the rear No. 2 drive shaft inboard joint boot clamp as shown in the illustration.


Hide 42347D 2.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the rear No. 2 drive shaft inboard joint boot clamp.


Hide 3.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT

a.

Separate the rear drive shaft inboard joint boot from the rear drive shaft inboard joint assembly.


Hide 4.REMOVE REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the rear drive shaft inboard joint assembly.


b.
C160821C16
1.427,1.198 1.427,0.646 true 1.802,0.76 1.802,0.448 1.802,0.448 1.521,0.448 true 1.427,0.688 1.427,0.448 false 1.115,0.448 1.521,0.448 false 0.969,0.375 1.156,0.542 0.188,0.167 10 *a
*a Matchmark


Put matchmarks on the rear drive shaft inboard joint assembly and rear drive shaft outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the rear drive shaft inboard joint assembly from the rear drive shaft outboard joint shaft assembly.


d.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C160822

Using a snap ring expander, remove the shaft snap ring from the rear drive shaft outboard joint shaft assembly.


f.
C162724C09
2.906,0.531 1.521,0.313 1.521,0.313 3,0.615 false 1.344,0.24 1.542,0.406 0.198,0.167 10 *a
*a Matchmark


Put matchmarks on the rear drive shaft outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the rear drive shaft outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




Hide 5.REMOVE REAR DRIVE SHAFT INBOARD JOINT BOOT

a.

Remove the rear No. 2 drive shaft inboard joint boot clamp, rear drive shaft inboard joint boot and rear drive shaft inboard joint boot clamp.


Hide 42346F 6.SEPARATE REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C106168

Using pliers, separate the rear No. 2 drive shaft outboard joint boot clamp as shown in the illustration.


Hide 42346D 7.SEPARATE REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the rear No. 2 drive shaft outboard joint boot clamp.


Hide 8.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT

a.

Remove the rear drive shaft outboard joint boot clamp, rear drive shaft outboard joint boot and rear No. 2 drive shaft outboard joint boot clamp from the rear drive shaft outboard joint shaft assembly.


b.

Remove the old grease from the outboard joint.