Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _094408 STOP AND START _0444545 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  STA Signal Circuit  


DESCRIPTION

While the engine is being cranked, a starter operation request signal is sent to terminal STA of the ECM.

HINT:

If there is an open in the STA circuit of the ECM, stop and start control will be prohibited after the third time the engine is started by stop and start control.

·

Stop and start control will be prohibited until the ignition switch is turned off.

·

The MIL will not illuminate.

·

If there is an open in the STA circuit of the ECM, the engine can still be started using the push start switch assembly, as the ECM also receives the starter operation request signal from the engine stop and start ECU via CAN communication. (Stop and start control is prohibited as the reliability of the signal sent via CAN communication cannot be assured while the voltage drops during operation of the starter assembly.)



A347476E23
2.667,0.51 4.604,0.75 1.938,0.24 10 false Starter operation request signal 4.26,1.615 5.823,1.833 1.563,0.219 10 false Starter operation request 4.26,2.094 5.823,2.313 1.563,0.219 10 false Starter operation request 5.958,2.51 7.01,2.865 1.052,0.354 10 false Engine Stop and Start ECU 2.385,2.115 3,2.313 0.615,0.198 10 false Open 0.583,2.51 1.042,2.708 0.458,0.198 10 false ECM 0.781,1.875 1.24,2.073 0.458,0.198 10 false STA 6.146,1.885 6.604,2.083 0.458,0.198 10 false STA 6.156,0.833 6.615,1.031 0.458,0.198 10 false CAN 0.75,0.823 1.208,1.021 0.458,0.198 10 false CAN 0.875,3.25 3.625,3.448 2.75,0.198 10 false from ST NO. 1 Fuse 0.833,4.74 3.896,4.938 3.063,0.198 10 false for Starter Assembly 3.885,4 5.115,4.198 1.229,0.198 10 false ST 0.396,5.333 2.156,5.552 1.76,0.219 10 false : CAN Communication Line

WIRING DIAGRAM

A459371E01
0.969,0.698 1.583,0.896 0.615,0.198 10 false CANH 0.99,1.094 1.604,1.292 0.615,0.198 10 false CANL 1.063,1.573 1.677,1.771 0.615,0.198 10 false STA 1.427,0.531 1.979,0.708 0.552,0.177 10 false 13 1.427,0.927 1.979,1.104 0.552,0.177 10 false 26 1.427,1.469 1.979,1.646 0.552,0.177 10 false 43 0.667,2.385 1.281,2.583 0.615,0.198 10 false A28 1.021,2.385 1.635,2.583 0.615,0.198 10 false ECM 5.896,0.698 6.51,0.896 0.615,0.198 10 false CANH 5.896,1.104 6.51,1.302 0.615,0.198 10 false CANL 5.896,1.573 6.51,1.771 0.615,0.198 10 false STA 5.5,0.708 5.927,0.875 0.427,0.167 10 false H66 5.5,1.104 5.927,1.271 0.427,0.167 10 false H66 5.5,1.573 5.927,1.74 0.427,0.167 10 false A34 5.563,0.5 5.99,0.667 0.427,0.167 10 false 13 5.563,0.917 5.99,1.083 0.427,0.167 10 false 14 5.563,1.375 5.99,1.542 0.427,0.167 10 false 21 3.01,4.281 3.625,4.479 0.615,0.198 10 false ST 3.406,3.448 3.938,3.635 0.531,0.188 10 false 3 3.406,3.854 3.938,4.042 0.531,0.188 10 false 2 2.667,3.448 3.198,3.635 0.531,0.188 10 false 5 2.667,3.865 3.198,4.052 0.531,0.188 10 false 1 1.656,3.708 2.323,3.99 0.667,0.281 10 false ST NO. 1 0.76,4.083 1.375,4.281 0.615,0.198 10 false FL MAIN 0.875,4.698 1.49,4.896 0.615,0.198 10 false Battery 1.573,5.323 3.302,5.625 1.729,0.302 10 false : CAN Communication Line 5.698,4.635 6.823,4.938 1.125,0.302 10 false Starter Assembly 5.531,4.167 6.656,4.469 1.125,0.302 10 false C58 5.875,3.563 6.802,3.844 0.927,0.281 10 false ST 5.604,3.354 5.885,3.542 0.281,0.188 10 false 1 5.427,2.385 7.125,2.688 1.698,0.302 10 false Engine Stop and Start ECU 5.885,4.167 6.344,4.365 0.458,0.198 10 false ZYV 5.521,3.563 6.646,3.865 1.125,0.302 10 false C56 5.604,3.979 5.885,4.167 0.281,0.188 10 false 1 4.635,4.302 5.333,4.573 0.698,0.271 10 false ST NO. 2

PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Read the values displayed on the GTS when the ignition switch is ON and on (START).

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
GTS Display Condition Normal Condition
Starter SW Ignition switch ON OFF
Engine START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
2.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-43 (STA) - 2 (ST relay) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR