Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  Display does not Dim when Light Control Switch is Turned ON  


DESCRIPTION

When the navigation system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

The radio receiver assembly switches between the daytime screen and night screen on the multi-display assembly according to the illumination signal input.

WIRING DIAGRAM

E380006E39
1.031,0.667 2.229,0.948 1.198,0.281 10 false from TAIL Relay 2.76,0.854 3.354,1.115 0.594,0.26 10 false PANEL 0.865,4.406 3.135,4.646 2.271,0.24 10 false : AVC-LAN Communication Line 4.896,0.542 5.49,0.802 0.594,0.26 10 false 2 4.854,1.063 5.448,1.323 0.594,0.26 10 false 13 5.115,0.677 5.708,0.938 0.594,0.26 10 false ILL 5.125,1.167 5.719,1.427 0.594,0.26 10 false GND1 4.844,1.583 5.438,1.844 0.594,0.26 10 false H7 4.854,1.75 6.333,1.969 1.479,0.219 10 false Multi-display Assembly 4.74,2.646 5.333,2.906 0.594,0.26 10 false 15 4.729,2.875 5.323,3.135 0.594,0.26 10 false H5 5.125,2.875 5.719,3.135 0.594,0.26 10 false ILL+ 5.125,3.51 5.719,3.771 0.594,0.26 10 false GND1 4.771,3.302 5.365,3.563 0.594,0.26 10 false 1 4.74,3.521 5.333,3.781 0.594,0.26 10 false H4 4.667,3.906 6.438,4.177 1.771,0.271 10 false Radio Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK SYMPTOMS
a.

Check the symptoms that occur by viewing the display.

HINT:
·

When the navigation system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

·

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

·

The radio receiver assembly switches between the daytime screen and night screen on the multi-display assembly according to the illumination signal input.




Result:
Result Proceed to
There is a delay until the display dims after the navigation system is activated with the light control switch in the tail or head position. A
The display dims for a moment and then becomes bright after the navigation system is activated with the light control switch in the tail or head position. B
When the light control switch is set to the tail or head position, the display dims but does not switch to the night screen.
When the light control switch is set to the tail or head position, the display neither dims nor switches to the night screen. C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

3.CHECK IMAGE QUALITY SETTING

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the H7 multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H7-2 (ILL) - H7-13 (GND1) Ignition switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK IMAGE QUALITY SETTING
a.

Turn the light control switch to the tail or head position.


b.

Check that the daytime screen setting on the display adjustment screen is set to on.


Result:
Result Proceed to
Daytime screen setting is set to on. A
Daytime screen setting is set to off. B



A

CHANGE DAYTIME SCREEN SETTING TO OFF

B

4.CHECK VEHICLE SIGNAL (OPERATION CHECK)
4.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E225854

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the light control switch operation.

OK:
Light Control Switch Display
Tail or head ON
except Tail or head OFF


HINT:
·

This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.

·

Make sure to move the vehicle to a bright area before performing an operation check with the light control switch in the AUTO position.




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the H5 and H4 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H5-15 (ILL+) - H4-1 (GND1) Ignition switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR