Home › Engine / Hybrid System › 2GR-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2020.11
RM37A0E _51 Engine / Hybrid System _086857 2GR-FKS STARTING _0445312 STARTER(w/ Stop And Start System) A

2GR-FKS STARTING  STARTER(w/ Stop And Start System)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE WIRE HARNESS

a.
A454701

Remove the 2 nuts and wire harness from the starter assembly.


Hide 2.REMOVE STARTER INRUSH CURRENT REDUCTION RELAY

a.
A454702

Remove the nut and disconnect the field coil lead wire from terminal M.


b.
A454703

Remove the 2 bolts and starter inrush current reduction relay from the starter drive housing assembly.


Hide 28226B 3.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A454704

While holding the magnet starter switch assembly to the starter drive housing assembly, remove the 2 nuts.


b.
A458863C01
0.74,0.5 0.927,0.188 0.927,0.188 1.146,0.188 false 2.188,0.479 2.375,0.167 2.375,0.167 2.594,0.167 true 1.177,0.063 1.49,0.26 0.313,0.198 10 false *a 2.646,0.052 2.958,0.25 0.313,0.198 10 false *1
*1 Pinion Drive Lever
*a Hook


While lifting the rear of the magnet switch, remove the hook from the pinion drive lever, then remove the magnet starter switch assembly.


Hide 28120 4.REMOVE STARTER YOKE ASSEMBLY

a.
A454706C01
0.271,1.813 0.594,1.813 false 1.688,1.896 1.688,1.688 false 1.635,1.917 1.948,2.073 0.313,0.156 10 false *1 0.125,1.708 0.438,1.865 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Using a T25 "TORX" socket wrench, remove the 2 through bolts, and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 28130 5.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A454707

Remove the 2 screws.


b.
A455720C01
0.542,1.667 0.729,1.667 0.729,1.667 0.938,1.479 false 1.25,1.896 1.479,1.896 1.479,1.896 1.698,1.708 false 1.313,0.604 1.729,0.604 false 0.396,1.573 0.594,1.802 0.198,0.229 10 false *1 1.094,1.802 1.333,2.042 0.24,0.24 10 false *2 1.792,0.49 2.031,0.729 0.24,0.24 10 false *a
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly
*a Field Coil Lead Wire


While holding down the field coil lead wire, remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 6.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A064784C06
1.073,0.208 1.313,0.208 1.313,0.208 1.552,0.51 false 1.948,0.563 2.167,0.219 2.167,0.219 2.396,0.219 false 2.458,0.094 2.771,0.25 0.313,0.156 10 false *a 0.885,0.104 1.198,0.26 0.313,0.156 10 false *b
*a Brush Spring
*b Brush


Using a screwdriver, hold the brush spring back and disconnect the 4 brushes.


b.

Remove the starter brush holder assembly from the starter armature assembly.


Hide 28160 7.REMOVE STARTER ARMATURE ASSEMBLY

a.
A202438C01
1.49,0.406 1.938,0.229 1.938,0.229 2.188,0.229 false 1.615,1.958 1.823,1.958 1.823,1.958 2.073,1.635 false 2.229,0.135 2.542,0.333 0.313,0.198 10 false *1 1.417,1.885 1.729,2.083 0.313,0.198 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly from the starter yoke assembly.


Hide 8.REMOVE STARTER ARMATURE PLATE

a.
A396261C01
1.063,0.979 0.75,0.458 0.75,0.458 0.563,0.458 false 1.635,1.99 1.771,1.99 1.771,1.99 1.833,1.635 false 2.688,1.781 2.688,1.427 false 0.313,1.802 0.313,1.542 false 0.229,1.813 0.542,1.969 0.313,0.156 10 false *1 2.625,1.802 2.938,1.958 0.313,0.156 10 false *2 0.406,0.375 0.719,0.531 0.313,0.156 10 false *3 1.479,1.906 1.792,2.063 0.313,0.156 10 false *3
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*3 Starter Armature Plate


Remove the starter armature plate from the starter drive housing assembly or starter yoke assembly.


Hide 9.REMOVE PLANETARY GEAR

a.
A396262

Remove the 3 planetary gears from the starter drive housing assembly.


Hide 10.REMOVE RUBBER SEAL

a.
A396263

Remove the rubber seal from the starter drive housing assembly.