Home › Engine / Hybrid System › 2GR-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2020.11
RM37A0E _51 Engine / Hybrid System _086857 2GR-FKS STARTING _0445312 STARTER(w/ Stop And Start System) A

2GR-FKS STARTING  STARTER(w/ Stop And Start System)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL RUBBER SEAL

a.
A396263

Install the rubber seal to the starter drive housing assembly.


Hide 2.INSTALL PLANETARY GEAR

a.
A396268C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter drive housing assembly.


b.

Install the 3 planetary gears to the starter drive housing assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A347623

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.



Hide 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A211303

Hold the brush spring back and set the 4 brushes as shown in the illustration.


b.
A211304

Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes as shown in the illustration.


c.
A314282C02
1.396,0.219 1.552,0.219 1.552,0.219 2.458,0.771 true 2.51,0.563 2.938,0.156 2.938,0.156 3.073,0.156 true 2.167,1.542 2.302,1.542 2.302,1.542 2.51,0.958 true 1.208,0.104 1.521,0.26 0.313,0.156 10 false *a 3.146,0.063 3.375,0.219 0.229,0.156 10 false *b 1.99,1.438 2.302,1.594 0.313,0.156 10 false *c
*a Grommet
*b Negative (-) Brush Holder Plate
*c Positive (+) Motor Lead Wire


Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A454708C02
1.667,1.979 1.854,1.979 1.854,1.979 2.115,1.177 true 0.625,1.76 0.833,1.76 0.833,1.76 1.281,0.854 true 1.854,0.26 2.01,0.26 2.01,0.26 2.292,0.385 false 0.469,1.667 0.781,1.823 0.313,0.156 10 false *a 1.51,1.885 1.823,2.042 0.313,0.156 10 false *b 1.708,0.167 2.021,0.323 0.313,0.156 10 false *a
*a Field Coil Lead Wire Rubber
*b Cutout


Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

Align the field coil lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.



b.
A454707

Install the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 6.INSTALL STARTER ARMATURE PLATE

a.
A454709C01
1.979,1.302 2.354,0.615 2.354,0.615 2.573,0.615 true 2.646,1.854 2.99,1.49 2.99,1.49 3.156,1.49 true 2.51,1.188 2.75,0.969 2.75,0.969 2.896,0.969 false 0.75,1.75 0.948,1.75 0.948,1.75 1.177,1.406 false 1.646,1.542 1.438,1.958 1.438,1.958 1.229,1.958 true 0.583,1.656 0.896,1.813 0.313,0.156 10 false *1 2.948,0.854 3.26,1.01 0.313,0.156 10 false *2 2.635,0.51 2.948,0.667 0.313,0.156 10 false *a 3.219,1.385 3.427,1.604 0.208,0.219 10 false *b 1.073,1.854 1.385,2.01 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Armature Plate
*a Stopper
*b Protrusion


Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.

NOTICE:

Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A454710C01
1.271,2.021 1.448,2.021 1.448,2.021 1.625,1.646 false 2.354,1.844 2.354,1.51 false 2.875,1.552 2.875,1.219 false 0.708,0.563 0.885,0.563 0.885,0.563 1.177,0.906 false 0.563,0.469 0.875,0.625 0.313,0.156 10 false *1 2.813,1.563 3.125,1.719 0.313,0.156 10 false *2 1.125,1.927 1.438,2.083 0.313,0.156 10 false *a 2.292,1.854 2.604,2.01 0.313,0.156 10 false *b
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*a Cutout
*b Protrusion


Align the cutout of the starter yoke assembly with the protrusion of the starter drive housing assembly.


b.
A454706

Using a T25 "TORX" socket wrench, install the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226B 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A458864C01
2.594,0.146 2.365,0.146 2.365,0.146 2.188,0.49 true 0.365,0.188 0.583,0.188 0.583,0.188 0.708,0.5 true 0.219,0.094 0.531,0.25 0.313,0.156 10 false *a 2.635,0.042 2.948,0.198 0.313,0.156 10 false *1
*1 Pinion Drive Lever
*a Hook
V100135

High-temperature Grease


Apply high-temperature grease to the magnet starter switch assembly as shown in the illustration.


b.

Hang the hook of the magnet starter switch assembly on the pinion drive lever.


c.
A454704

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 9.INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

a.
A454703

Install the starter inrush current reduction relay to the starter drive housing assembly with the 2 bolts.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


b.
A454702

Connect the field coil lead wire to terminal M with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 10.INSTALL WIRE HARNESS

a.
A454701

Install the wire harness to the starter assembly with the 2 nuts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)