Home › General › SPECIFICATIONS › 2GR-FKS STARTING › from 2020.11
RM37A0E _V1 General _086915 SPECIFICATIONS _0415875 2GR-FKS STARTING F

SPECIFICATIONS  2GR-FKS STARTING  SERVICE DATA  


Starter Assembly (w/ Stop And Start System)
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 100 A

Starter Armature Assembly (w/ Stop And Start System)
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω
Segment - Starter armature core 10 kΩ or higher

Commutator runout Maximum runout 0.05 mm (0.00197 in.)

Commutator diameter Standard diameter 29 mm (1.14 in.)
Minimum diameter 28 mm (1.10 in.)

Undercut depth Standard undercut depth 0.7 mm (0.0276 in.)
Minimum undercut depth 0.2 mm (0.00787 in.)

Starter Brush Holder Assembly (w/ Stop And Start System)
Brush length Standard length 14.4 mm (0.567 in.)
Minimum length 9.0 mm (0.354 in.)

Tester Connection Condition Specified Condition
A - B
A - C
B - D
C - D
Always 10 kΩ or higher
A - D
B - C
Below 1 Ω

Brush spring load Standard spring load 22.3 to 27.3 N (2.27 to 2.78 kgf, 5.01 to 6.14 lbf)
Minimum spring load 13.8 N (1.41 kgf, 3.1 lbf)

Magnet Starter Switch Assembly (w/ Stop And Start System)
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω
Terminal 50 - Magnet starter switch assembly body Below 2 Ω

Starter Assembly (w/o Stop And Start System)
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A

Starter Armature Assembly (w/o Stop And Start System)
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω
Segment - Starter armature core 10 kΩ or higher

Commutator length Standard length 3.1 mm (0.122 in.)
Maximum length 3.8 mm (0.150 in.)

Starter Commutator End Frame Assembly (w/o Stop And Start System)
Brush length Standard length 9.0 mm (0.354 in.)
Minimum length 4.0 mm (0.157 in.)

Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher

Magnet Starter Switch Assembly (w/o Stop And Start System)
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω
Terminal 50 - Magnet starter switch assembly body Below 2 Ω

Engine Switch
Tester Connection Condition Specified Condition
5 (SS1) - 6 (AGND)
1 (SS2) - 6 (AGND)
Not pushed 10 kΩ or higher
Pushed Below 1 Ω

Condition Specified Condition
Battery positive (+) → Terminal 9 (SWIL)
Battery negative (-) → Terminal 6 (AGND)
Illuminates

ST Relay
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω