DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Collision System / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | - | - | - | Cannot be used |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| PCS Function ON/OFF State | Pre-collision system status | ON / OFF | ON: Pre-collision system enabled
OFF: Pre-collision system disabled |
- |
| PBA Request | Pre-collision brake assist operation status | Not PBA Request / PBA Standby Request / PBA Request Level 1 / PBA Request Level 2 | Not PBA Request: Pre-collision brake assist not requested
PBA Standby Request: Low pre-collision brake assist requested PBA Request Level 1: Medium pre-collision brake assist requested PBA Request Level 2: High pre-collision brake assist requested |
The value changes in accordance with the possibility of a collision. This item indicates the pre-collision brake assist standby status. Whether pre-collision brake assist is applied or not is determined by the depression of the brake pedal. |
| VGRS Activation Request | - | - | - | Cannot be used |
| Warning Brake Request | - | - | - | Cannot be used |
| FPB Request | Skid control ECU PCS brake request (pre-braking) | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PB Request | Pre-collision brake request status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| AVS Control Request | - | - | - | Cannot be used |
| Prefill | Skid control ECU PCS brake assist standby | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PBR Request | PBR operation status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PBH Request | PBH operation status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PCS PBA Invalid | PCS PBA status | OFF / ON | OFF: Valid
ON: Invalid |
- |
| PCS Warning Buzzer Invalid | PCS warning buzzer status | OFF / ON | OFF: Valid
ON: Invalid |
- |
| PCS PB Invalid | PCS PB Status | OFF / ON | OFF: Valid
ON: Invalid |
- |
| Acceleration Suppression at Low Speed (A Control) Invalid | Acceleration suppression at low speed (A control) invalid status | OFF / ON | OFF: Acceleration suppression at low speed (A control) function valid
ON: Acceleration suppression at low speed (A control) function invalid |
Cannot be used |
| Emergency Steering Assist Invalid 1 | Emergency Steering Assist Invalid 1 status | OFF / ON | OFF: Emergency steering assist invalid 1 function valid
ON: Emergency steering assist invalid 1 function invalid |
- |
| PCS Warning Display Request | PCS warning message status | Not Request / PCS Warning Display 1 Request / PCS Warning Display 2 Request / PCS Warning Display 3 Request | Not Request: No message
PCS Warning Display 1 Request: Displayed PCS Warning Display 2 Request: Not used PCS Warning Display 3 Request: Not used |
- |
| PCS Warning Buzzer Request | PCS meter buzzer operation status | OFF / ON | OFF: Not sounding
ON: Sounding |
- |
| Vehicle Information (Conv/HV/EV) | Vehicle information (Conv/HV/EV) | Unknown / Conv / HV/EV | Unknown: Vehicle information not confirmed
Conv: Conventional HV/EV: Hybrid vehicle |
- |
| Vehicle Information (Transmission Type) | Vehicle information (transmission type) | MT, AT, CVT, MMT, SMT, HV/EV - AT or Unknown | Displays the type of transmission | - |
| Power Steering Control Module Equipped Information | Power steering control module is installed or not | Absence or Presence | Absence: Not equipped
Presence: Equipped |
- |
| VGRS ECU Equipped Information | Variable gear ratio steering system function availability | Unknown, Absence or Presence | Unknown: Vehicle information not confirmed
Absence: Variable gear ratio steering system absence Presence: Variable gear ratio steering system presence |
- |
| PCS Function ON/OFF State Stored | Pre-collision system on/off setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. | Not Stored / Stored | Not Stored: Defaults to on
Stored: Maintains last on/off status |
"PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 2 | Sensitivity setting of the pre-collision system when the pre-collision system is turned on and the ignition switch is turned off and then to ON. | Not Stored / Stored | Not Stored: Defaults to middle
Stored: Maintains last setting |
"PCS Warning Timing State Stored 2" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 3 | Sensitivity setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. | Not Stored / Stored | Not Stored: Defaults to middle
Stored: Maintains last setting |
"PCS Warning Timing State Stored 3" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 1 | Sensitivity setting of the pre-collision system when the pre-collision system is turned off and then on with the ignition switch ON. | Not Stored / Stored | Not Stored: Defaults to middle
Stored: Maintains last setting |
"PCS Warning Timing State Stored 1" is a customizable item which can be set using the GTS. |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Collision System / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Warning Buzzer | Sounds the meter buzzer | Start / Stop | Test possible with ignition switch ON, vehicle stopped |