1.INSPECT SPEEDOMETER
The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake booster with master cylinder assembly) because it is the source of the vehicle speed signal.
Data List values of the skid control ECU (brake booster with master cylinder assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Brake/EPB / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| Vehicle Speed |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.0 to 25.0 |
| 40 | 41.7 to 46.2 |
| 60 | 62.7 to 67.2 |
| 80 | 83.4 to 88.4 |
| 100 | 104.3 to 109.3 |
| 120 | 125.1 to 130.6 |
| 140 | 145.8 to 151.8 |
| 160 | 166.2 to 173.2 |
| 180 | 186.9 to 194.5 |
| 200 | 207.7 to 215.7 |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 20.3 to 22.3 |
| 40 | 40.7 to 42.7 |
| 60 | 61.0 to 63.0 |
| 80 | 81.4 to 83.4 |
| 100 | 101.7 to 103.7 |
| 120 | 122.1 to 124.1 |
| 140 | 142.4 to 144.4 |
| 160 | 162.7 to 164.7 |
| 180 | 183.1 to 185.1 |
| 200 | 203.4 to 205.4 |
| GTS Indication (mph) | Acceptable Range (mph) |
|---|---|
| 20 | 21.0 to 23.5 |
| 40 | 42.0 to 44.5 |
| 60 | 62.5 to 66.0 |
| 80 | 83.1 to 87.1 |
| 100 | 103.9 to 108.4 |
| 120 | 124.7 to 129.6 |
Speedometer reading is within the acceptable range at each vehicle speed.
2.INSPECT TACHOMETER (for Gasoline Model)
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 650 to 750 rpm: Idling (shift lever in N, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Tester Display |
|---|
| Engine Speed |
| GTS Indication (rpm) | Acceptable Range (rpm) |
|---|---|
| 700 | 630 to 770 |
| 1000 | 900 to 1100 |
| 2000 | 1850 to 2150 |
| 3000 | 2800 to 3200 |
| 4000 | 3800 to 4200 |
| 5000 | 4800 to 5200 |
| 6000 | 5750 to 6250 |
| 7000 | 6700 to 7300 |
Tachometer reading is within the acceptable range at each engine speed.
3.INSPECT WARNING OR INDICATOR LIGHT ILLUMINATION (INITIAL CHECK)
for HV Model
Turn the ignition switch off.
Turn the ignition switch to ON or ON (READY), and check the operation of the warning and indicator lights in the following table.
The illumination of each warning light and indicator light varies.
All of the lights illuminate and then turn off.
| Warning or Indicator Light |
|---|
| SRS warning light |
| EPS warning light |
| MIL (Check engine warning light) |
| Charge warning light |
| Brake warning light/red (malfunction) |
| Brake warning light/yellow (minor malfunction) |
| Brake hold standby indicator light |
| ABS warning light |
| VSC OFF indicator light |
| Slip indicator light |
| Speed warning light*5 |
| Tire pressure warning light*6 |
| PCS warning light*1 |
| Clearance sonar OFF indicator light*2 |
| PKSB OFF indicator light*2, *3 |
| BSM OFF indicator light*4 |
*1: w/ Forward Recognition Camera
*2: w/ TOYOTA Parking Assist-sensor System
*3: w/ Parking Support Brake System
*4: w/ Blind Spot Monitor System
*5: w/ Speed warning
*6: w/ Tire Pressure Warning System
for Gasoline Model
Turn the ignition switch off.
Turn the ignition switch to ON, and check the operation of the warning and indicator lights in the following table.
The illumination of each warning light and indicator light varies.
All of the lights illuminate and then turn off.
| Warning or Indicator Light |
|---|
| SRS warning light |
| EPS warning light |
| MIL (Check engine warning light) |
| Charge warning light |
| Brake warning light/red (malfunction) |
| Brake warning light/yellow (minor malfunction) |
| Brake hold standby indicator light |
| ABS warning light |
| VSC OFF indicator light |
| Slip indicator light |
| Tire pressure warning light*6 |
| Stop and start off indicator light*5 |
| Stop and start indicator light*5 |
| Eco driving indicator light |
| PCS warning light*1 |
| Clearance sonar OFF indicator light*2 |
| PKSB OFF indicator light*2, *3 |
| BSM OFF indicator light*4 |
| Downhill assist control indicator light |
*1: w/ Forward Recognition Camera
*2: w/ TOYOTA Parking Assist-sensor System
*3: w/ Parking Support Brake System
*4: w/ Blind Spot Monitor System
*5: w/ Stop and Start System
*6: w/ Tire Pressure Warning System