PRECAUTION FOR OPERATION CHECK
Use the correct procedure to replace the airbag parts.
CHECK SRS WARNING LIGHT
Primary check
Turn the ignition switch to ON and check that the SRS warning light turns on.
Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. Check that the SRS warning light illuminates for approximately 6 seconds while diagnosis of the airbag system is performed.
If the SRS warning light remains on for more than approximately 6 seconds after the ignition switch is turned to ON, the airbag system may be malfunctioning.
If the SRS warning light occasionally turns on after the ignition switch has been ON for approximately 6 seconds, there may be an open, or short to +B or ground in the SRS warning light circuit.
If the SRS warning light illuminates after the ignition switch is turned off or to ACC, there may be a malfunction in the airbag sensor assembly power source circuit or combination meter assembly.
After the initial check, if the SRS warning light turns off and then on repeatedly, a drop in airbag sensor assembly power source voltage is occurring. The SRS warning light will turn off 10 seconds after the power source voltage returns to normal.
FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)
Initial check
Turn the ignition switch to ON.
The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.
Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cut off switch cylinder sub-assembly condition as listed below.
| Airbag Cut Off Switch Cylinder Sub-assembly Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
|
*: The ON indicator illuminates for approximately 60 seconds and then turns off. |
|||
| ON | ON* | OFF | OFF |
| OFF | OFF | ON | OFF |
| Switch failure | OFF | ON | ON |
If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status and the SRS warning light is not illuminated, no DTC will be output. Therefore, perform troubleshooting for Trouble in Passenger Airbag ON/OFF Indicator.
PASSENGER AIRBAG ON/OFF INDICATOR CHECK (w/ Airbag Cut Off Switch)
| *A | for Type A |
| *B | for Type B |
Turn the ignition switch to ON.
Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, then turns off for approximately 2 seconds.
Refer to the indicator operation table in Function of Passenger Airbag ON/OFF Indicator for the passenger airbag ON/OFF indicator operation when the ignition switch is turned to ON and approximately 6 seconds elapse.
INSPECT AIRBAG COMPONENTS
Inspect the SRS parts in table below.
| Component to Inspect | Procedure |
|---|---|
| Horn button assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the horn button assembly installed to the vehicle.
If any defects are found, replace the horn button assembly with a new one. |
| Lower No. 1 instrument panel airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the lower No. 1 instrument panel airbag assembly installed to the vehicle.
If any defects are found, replace the lower No. 1 instrument panel airbag assembly with a new one. |
| Instrument panel passenger airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the instrument panel passenger airbag assembly installed to the vehicle.
If any defects are found, replace the instrument panel safety pad sub-assembly with a new one. |
| Curtain shield airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the curtain shield airbag assemblies installed to the vehicle.
If any defects are found, replace each pillar garnish or the roof headlining assembly with a new one. |
| Front seat airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the front seat airbag assemblies installed to the vehicle.
If any defects are found, replace the separate type front seatback pad or separate type front seatback cover with a new one. |
| Front seat outer belt assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the front seat outer belt assemblies installed to the vehicle.
If any defects are found, replace the front seat outer belt assembly with a new one. |
| Rear seat outer belt assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the rear seat outer belt assemblies installed to the vehicle.
If any defects are found, replace the rear seat outer belt assembly with a new one. |
| Airbag sensor assembly | 1.
Perform a diagnostic system check. |
| Front airbag sensor | |
| Side airbag sensor assembly | |
| Rear airbag sensor | |
| Harness and connector |