Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2020.11–2021.10
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Grille Shutter Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Grille Shutter Communication Stop Mode Communication stop for "Grille Shutter" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Swing grille actuator assembly branch line or connector

·

Power source circuit of swing grille actuator assembly

·

Swing grille actuator assembly ground circuit

·

Swing grille actuator assembly



WIRING DIAGRAM

C427512E02
5.49,4.031 6.823,4.521 1.333,0.49 10 false Swing Grille Actuator Assembly 0.427,1.833 3.063,2.219 2.635,0.385 10 false No. 5 Global CAN Junction Connector 5.188,4.031 5.646,4.281 0.458,0.25 10 false A52 0.125,1.833 0.719,2.094 0.594,0.26 10 false H94 1.708,0.76 2.302,1.021 0.594,0.26 10 false 7 1.667,1.344 2.26,1.604 0.594,0.26 10 false 17 5.375,0.76 5.969,1.021 0.594,0.26 10 false 6 5.604,0.865 6.198,1.125 0.594,0.26 10 false CANP 5.594,1.469 6.188,1.729 0.594,0.26 10 false CANN 5.604,2.479 6.198,2.74 0.594,0.26 10 false +B 5.594,3.083 6.188,3.344 0.594,0.26 10 false GND 5.375,1.313 5.917,1.542 0.542,0.229 10 false 5 5.375,2.354 5.917,2.583 0.542,0.229 10 false 1 5.385,2.948 5.927,3.177 0.542,0.229 10 false 3 3.75,2.354 4.813,2.594 1.063,0.24 10 false ECU-B NO. 2 1.646,2.479 3.292,2.813 1.646,0.333 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A52 swing grille actuator assembly connector.


c.
C378928C52
1.5,0.125 1.927,0.385 0.427,0.26 2.281,1.885 2.115,1.885 2.115,1.885 2.115,1.219 true 1.781,1.885 1.948,1.885 1.948,1.885 1.948,1.219 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 1.594,0.177 1.906,0.375 0.313,0.198 10 false A52 2.365,1.823 2.885,2.031 0.521,0.208 10 false CANP 1.333,1.813 1.854,2.021 0.521,0.208 10 false CANN
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-6(CANP) - A52-5(CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349838C48
1.458,0.156 1.875,0.417 0.417,0.26 1.156,1.802 1.313,1.802 1.313,1.802 1.313,1.229 true 1.771,1.833 1.625,1.833 1.625,1.833 1.625,1.229 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.875,1.771 2.313,1.969 0.438,0.198 10 false GND 0.927,1.75 1.365,1.948 0.438,0.198 10 false +B 1.563,0.208 2,0.406 0.438,0.198 10 false A52
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-3 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-1 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)