Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Integration Control and Panel Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Integration Control and Panel Assembly Communication Stop Mode Communication stop for "D-SEAT SW" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Integration control sub-assembly branch line or connector

·

Power source circuit of integration control sub-assembly

·

Integration control sub-assembly ground circuit

·

Integration control sub-assembly



WIRING DIAGRAM

C427168E05
0.156,1.844 0.771,2.042 0.615,0.198 10 false H91 0.479,1.844 3.177,2.146 2.698,0.302 10 false No. 3 Global CAN Junction Connector 1.667,1.365 2.01,1.563 0.344,0.198 10 false 17 1.708,0.781 2.052,0.979 0.344,0.198 10 false 7 5.323,0.792 5.667,0.99 0.344,0.198 10 false 32 5.323,1.375 5.667,1.573 0.344,0.198 10 false 31 5.583,0.906 6.125,1.115 0.542,0.208 10 false CANP 5.594,1.458 6.135,1.667 0.542,0.208 10 false CANN 5.604,2.365 6.146,2.573 0.542,0.208 10 false B 5.594,2.948 6.135,3.156 0.542,0.208 10 false ACC 5.594,3.521 6.135,3.729 0.542,0.208 10 false IG+ 5.594,4.052 6.135,4.26 0.542,0.208 10 false GND 5.323,3.906 5.865,4.115 0.542,0.208 10 false 20 5.385,3.396 5.927,3.604 0.542,0.208 10 false 4 5.375,2.813 5.917,3.021 0.542,0.208 10 false 3 5.365,2.219 5.906,2.427 0.542,0.208 10 false 1 2,2.917 4.469,3.396 2.469,0.479 10 false from ACC Relay 1.667,2.344 3.146,2.823 1.479,0.479 10 false from Auxiliary Battery 1.698,3.531 3.146,3.927 1.448,0.396 10 false from IG1-NO. 1 Relay 5.542,4.49 6.688,5.073 1.146,0.583 10 false Integration Control Sub-assembly 5.26,4.5 5.802,4.708 0.542,0.208 10 false H8 3.854,2.813 4.594,3.115 0.74,0.302 10 false ECU-ACC 3.719,2.219 4.708,2.51 0.99,0.292 10 false ECU-B NO. 2 3.656,3.385 4.781,3.625 1.125,0.24 10 false ECU-IG1 NO. 4

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (INTEGRATION CONTROL SUB-ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H8 integration control sub-assembly connector.


c.
C427495C01
1.458,0.25 1.896,0.49 0.438,0.24 1.708,2.708 1.875,2.708 1.875,2.708 1.875,1.958 true 2.167,2.708 2,2.708 2,2.708 2,1.958 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.604,0.281 1.917,0.479 0.313,0.198 10 false H8 2.229,2.625 2.74,2.875 0.51,0.25 10 false CANP 1.271,2.635 1.781,2.885 0.51,0.25 10 false CANN
*a Front view of wire harness connector
(to Integration Control Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-32 (CANP) - H8-31 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427495C02
1.458,0.25 1.896,0.49 0.438,0.24 0.594,2.719 0.427,2.719 0.427,2.719 0.427,1.969 true 0.813,1.125 0.646,1.125 0.646,1.125 0.646,1.708 true 0.698,0.792 0.531,0.792 0.531,0.792 0.531,1.708 true 0.417,0.542 0.25,0.542 0.25,0.542 0.25,1.708 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.604,0.281 1.917,0.479 0.313,0.198 10 false H8 0.5,0.469 1.01,0.719 0.51,0.25 10 false B 0.688,2.635 1.198,2.885 0.51,0.25 10 false GND 0.771,0.719 1.281,0.969 0.51,0.25 10 false ACC 0.906,1.042 1.417,1.292 0.51,0.25 10 false IG+
*a Front view of wire harness connector
(to Integration Control and Panel Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-20 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H8-1 (B) - Body ground Ignition switch off 11 to 14 V
H8-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V
H8-4 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)