AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK
Make sure that the customize settings are set to default when performing the automatic light control system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Turn the ignition switch to ON.
Turn the light control switch to the AUTO position.
Cover the automatic light control sensor.
Check that the taillights and low beam headlights come on.
Uncover the automatic light control sensor.
Check that the low beam headlights and taillights turn off.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (w/ Delay Function)
When the taillights are on (low beam headlights are not on)
Close all of the doors.
Turn the ignition switch to ON.
Turn the taillights on.
Turn the ignition switch off.
Open the driver door.
Check that all of the lights turn off immediately.
When the low beam headlights are on
Close all of the doors.
Turn the ignition switch to ON.
Turn the low beam headlights on.
Turn the ignition switch off.
Open any of the doors.
Close the door.
Check that all of the lights turn off after 30 seconds (delay function).
Before the lights turn off, if the lock button on the key is pushed after all of the doors are locked, all of the lights will turn off immediately.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (for Driver Door-linked Auto Light Turn-off System)
Make sure that the customize settings are set to default when performing the light auto turn-off system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Close all of the doors.
Turn the ignition switch to ON.
Turn the taillights, low beam headlights, high beam headlights, front fog lights and rear fog lights* on.
*: w/ Rear Fog Light
Turn the ignition switch off.
Open the driver door.
Check that all of the lights turn off immediately.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (except Driver Door-linked Auto Light Turn-off System)
When the light control switch is in the AUTO position
Turn the ignition switch to ON.
Turn the taillights, low beam headlights, high beam headlights, front fog lights and rear fog lights* on.
*: w/ Rear Fog Light
Turn the ignition switch off.
If the vehicle speed was not less than 10 km/h (6 mph) when the ignition switch was turned off, open the driver door.
Check that all of the lights turn off immediately.
When the light control switch is in the tail or head position
Turn the ignition switch to ON.
Turn the low beam headlights and high beam headlights on.
Turn the ignition switch off.
If the vehicle speed was not less than 10 km/h (6 mph) when the ignition switch was turned off, open the driver door.
Check that the low beam headlights and high beam headlights turn off immediately.
The taillights, clearance lights and license plate lights remain on.
DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK
Turn the ignition switch to ON (READY).*1
Start the engine.*2
Turn the light control switch to the off*3 or AUTO position (with the low beam headlights not turned on via the automatic light control system).
Release the parking brake.
Check that the daytime running lights come on.
*1: for HV Model
*2: for Gasoline Model
*3: w/ Light Control Switch Off Position
EXTENDED HEADLIGHT LIGHTING SYSTEM OPERATION CHECK (w/ Extended Headlight Lighting System)
Make sure that the customize settings are set to default when performing the extended headlight lighting system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Turn the ignition switch off.
Turn the light control switch to the AUTO position.
Pull the dimmer switch to flash the headlights once.
Check that the low beam headlights come on for approximately 30 seconds.
DOOR MIRROR FOOT LIGHT CONTROL OPERATION CHECK (w/ Door Mirror Foot Light)
Make sure that the customize settings are set to default when performing the door mirror foot light control operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
The operation and condition of this control are described below.
| Operation | Condition |
|---|---|
| Fade in and illuminate constantly | When any of the following conditions is met, the lights fade in and illuminate constantly:
·
A key is detected in the actuation area. ·
Any door is unlocked when the ignition switch is off and all of the doors are closed. |
| Illuminate for 15 seconds, and then fade out | When any of the following conditions is met, the lights illuminate for 15 seconds, and then fade out:
·
An actuation area-linked function is used.* ·
Any door is unlocked when the ignition switch is off and all of the doors are closed. |
| Fade out immediately | When the following condition is met, the lights fade out immediately:
·
The ignition switch is turned from off to ON. ·
A key is not detected in the actuation area. ·
All doors are locked when all doors are closed and any door is unlocked. |
*: When the lights are on, the lights fade out after approximately 3 seconds the key leaves the actuation areas around the doors.
MANUAL HEADLIGHT BEAM LEVEL CONTROL SYSTEM OPERATION CHECK
Turn the ignition switch to ON.
Turn the headlights on.
Turn the headlight leveling switch to "0".
Check that the headlight beam level changes when the headlight leveling switch is operated.
AUTOMATIC HIGH BEAM SYSTEM OPERATION CHECK (w/ Automatic High Beam System)
| *a | Automatic High Beam Indicator Light on Combination Meter Assembly |
| *b | Auto High Beam Switch Indicator |
Check the operation of the automatic high beam indicator light.
Turn the ignition switch to ON.
Turn the light control switch to the AUTO or head position.
Move the dimmer switch to the high position.
Press the auto high beam switch (indicator illuminates).
If the auto high beam switch is turned on when the light control switch is not in the AUTO or head position, or the dimmer switch is not in the high position, "To Activate Automatic High Beam, Switch Headlights to High Beam" will be displayed on the multi-information display.
Check that the automatic high beam indicator illuminates.
If the forward recognition camera cannot operate due to high vehicle interior temperatures, bad weather (rain, fog, etc.) or fogged up or dirty glass, the automatic high beam system will not operate and the automatic high beam indicator will not illuminate.
Check the operation of the automatic high beam function.
At night, when driving the vehicle with the automatic high beam system in standby mode, check that the high beams automatically turn on after a short delay when all of the following conditions are met:
The vehicle speed is more than approximately 30 km/h (19 mph). (except European Models)
The vehicle speed is more than approximately 40 km/h (25 mph). (for European Models)
The area in front of the vehicle is dark.
There are no oncoming vehicles with headlights on.
There are no preceding vehicles with taillights on.
There are few streetlights along the street ahead.
At night, when driving the vehicle with the high beams turned on by the automatic high beam system, check that the automatic high beam system turns off the high beams and returns to standby mode when any of the following conditions are met:
The vehicle speed is less than approximately 25 km/h (16 mph). (except European Models)
The vehicle speed is less than approximately 30 km/h (19 mph). (for European Models)
The level of ambient light is higher than a specified threshold.
There are oncoming vehicles with headlights on.
There are preceding vehicles with taillights on.
Light from streetlights ahead is higher than a specified threshold.