DESCRIPTION
When a pre-collision system DTC is stored, the forward recognition camera stores the current vehicle state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Collision System / Trouble Codes.
According to the display on the GTS, select a DTC to display its freeze frame data.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | - | - | - | Cannot be used |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| PCS Function ON/OFF State | Pre-collision system status | ON / OFF | ON: Pre-collision system enabled
OFF: Pre-collision system disabled |
- |
| PBA Request | Pre-collision brake assist operation status | Not PBA Request / PBA Standby Request / PBA Request Level 1 / PBA Request Level 2 | Not PBA Request: Pre-collision brake assist not requested
PBA Standby Request: Low pre-collision brake assist requested PBA Request Level 1: Medium pre-collision brake assist requested PBA Request Level 2: High pre-collision brake assist requested |
The value changes in accordance with the possibility of a collision. This item indicates the pre-collision brake assist standby status. Whether pre-collision brake assist is applied or not is determined by the depression of the brake pedal. |
| VGRS Activation Request | - | - | - | Cannot be used |
| Warning Brake Request | - | - | - | Cannot be used |
| FPB Request | Skid control ECU PCS brake request (pre-braking) | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PB Request | Pre-collision brake request status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| AVS Control Request | - | - | - | Cannot be used |
| Prefill | Skid control ECU PCS brake assist standby | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PBR Request | PBR operation status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PBH Request | PBH operation status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| PCS PBA Invalid | PCS PBA status | OFF / ON | OFF: Valid
ON: Invalid |
- |
| PCS Warning Buzzer Invalid | PCS warning buzzer status | OFF / ON | OFF: Valid
ON: Invalid |
- |
| PCS PB Invalid | PCS PB Status | OFF / ON | OFF: Valid
ON: Invalid |
- |
| Acceleration Suppression at Low Speed (A Control) Invalid | Acceleration suppression at low speed (A control) invalid status | OFF / ON | OFF: Acceleration suppression at low speed (A control) function valid
ON: Acceleration suppression at low speed (A control) function invalid |
Cannot be used |
| Emergency Steering Assist Invalid 1 | Emergency Steering Assist Invalid 1 status | OFF / ON | OFF: Emergency steering assist invalid 1 function valid
ON: Emergency steering assist invalid 1 function invalid |
- |
| PCS Warning Display Request | PCS warning message status | Not Request / PCS Warning Display 1 Request / PCS Warning Display 2 Request / PCS Warning Display 3 Request | Not Request: No message
PCS Warning Display 1 Request: Displayed PCS Warning Display 2 Request: Not used PCS Warning Display 3 Request: Not used |
- |
| PCS Warning Buzzer Request | PCS meter buzzer operation status | OFF / ON | OFF: Not sounding
ON: Sounding |
- |
| PCS Function ON/OFF State Stored | Pre-collision system on/off setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. | Not Stored / Stored | Not Stored: Defaults to on
Stored: Maintains last on/off status |
"PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 2 | Sensitivity setting of the pre-collision system when the pre-collision system is turned on and the ignition switch is turned off and then to ON. | Not Stored / Stored | Not Stored: Defaults to middle
Stored: Maintains last setting |
"PCS Warning Timing State Stored 2" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 3 | Sensitivity setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. | Not Stored / Stored | Not Stored: Defaults to middle
Stored: Maintains last setting |
"PCS Warning Timing State Stored 3" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 1 | Sensitivity setting of the pre-collision system when the pre-collision system is turned off and then on with the ignition switch ON. | Not Stored / Stored | Not Stored: Defaults to middle
Stored: Maintains last setting |
"PCS Warning Timing State Stored 1" is a customizable item which can be set using the GTS. |