Home › General › SPECIFICATIONS › P810 HYBRID TRANSMISSION / TRANSAXLE › 2020.11–2021.10
RM37A0E _V1 General _086915 SPECIFICATIONS _0415870 P810 HYBRID TRANSMISSION / TRANSAXLE F

SPECIFICATIONS  P810 HYBRID TRANSMISSION / TRANSAXLE  SERVICE DATA  


Hybrid Transaxle System
Maintenance mode engine idle speed Hybrid transaxle fluid temperature Hybrid transaxle fluid pressure
900 to 1000 rpm 20 to 50°C (68 to 122°F) 9.8 kPa (0.1 kgf/cm2, 1.4 psi) or more

Hybrid Transaxle Fluid

*: Using hybrid transaxle fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transaxle of the vehicle.

Hybrid transaxle fluid standard capacity (for Reference) Classification
4.4 liters (4.6 US qts, 3.9 Imp. qts) Toyota Genuine ATF WS*

Hybrid Transaxle Oil Seal
Front drive shaft oil seal RH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

Input Shaft Oil Seal
Input shaft type T oil seal Standard depth 1.9 to 2.7 mm (0.0748 to 0.106 in.)

Shift Lever
Shift lock control ECU
Inspect wire harness:
Tester Connection Condition Specified Condition
5 (IG) - Body ground Ignition switch ON (IG) 11 to 14 V
Ignition switch off Below 1 V
4 (STP) - Body ground Ignition switch ON (IG), brake pedal depressed 11 to 14 V
Ignition switch ON (IG), brake pedal released Below 1 V
1 (E) - Body ground Always Below 1 Ω
Inspect shift lock solenoid:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω
Transmission Control Switch (for LHD)
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher
Transmission Control Switch (for RHD)
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher

Shift Lever Position Sensor
Tester Connection Condition Specified Condition
7 (+B) - 3 (PR) Shift lever in P Below 1 Ω
7 (+B) - 4 (PNB) Below 1 Ω
7 (+B) - 8 (P) Below 1 Ω
7 (+B) - 1 (DB1), 2 (N), 6 (DB2) or 9 (R) Shift lever in P 10 kΩ or higher
7 (+B) - 3 (PR) Shift lever in R Below 1 Ω
7 (+B) - 9 (R) Below 1 Ω
7 (+B) - 1 (DB1), 2 (N), 4 (PNB), 6 (DB2) or 8 (P) Shift lever in R 10 kΩ or higher
7 (+B) - 2 (N) Shift lever in N Below 1 Ω
7 (+B) - 4 (PNB) Below 1 Ω
7 (+B) - 1 (DB1), 3 (PR), 6 (DB2), 8 (P) or 9 (R) Shift lever in N 10 kΩ or higher
7 (+B) - 1 (DB1) Shift lever in D or S Below 1 Ω
7 (+B) - 6 (DB2) Below 1 Ω
7 (+B) - 2 (N), 3 (PR), 4 (PNB), 8 (P) or 9 (R) Shift lever in D or S 10 kΩ or higher

Shift Paddle Switch
No. 1 transmission shift switch assembly
Tester Connection Condition Specified Condition
1 (SDN) - 2 (ECC) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
1 (SDN) - 3 (ECC1) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
No. 2 transmission shift switch assembly
Tester Connection Condition Specified Condition
1 (SUP) - 2 (ECC) "+" (Up shift) shift paddle switch operated and held Below 2.5 Ω
"+" (Up shift) shift paddle switch not operated 1 MΩ or higher

Relay
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω