Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0449687 DIFFERENTIAL OIL SEAL A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C378389N01
0.938,2.365 1.333,1.729 false 0.76,2.406 1.167,2.667 0.406,0.26 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

SST
09308-00010  

NOTICE:

Do not damage the automatic transaxle case sub-assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C361041N01
2.198,2.802 1.927,1.74 false 2.083,2.823 2.542,3.021 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09308-00010  

NOTICE:

Do not damage the transaxle housing.



Hide 43410M 4.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C400537C01
2.125,1.115 2.792,0.813 2.792,0.813 2.188,1.292 true 1.667,3.052 1.979,3.208 0.313,0.156 10 false *a 2.844,0.719 3.302,0.917 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09316-10010  
09950-70010  (09951-07150)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 43420H 5.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C361042C01
1.719,1.188 2.792,1.625 2.792,1.625 2.021,1.031 true 2.844,1.583 3.302,1.781 0.458,0.198 10 true SST 1.906,3.146 2.073,3.333 0.167,0.188 10 true *a
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.