35572A
1.REMOVE TRANSMISSION CONTROL SHAFT LEVER
Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.
84540
2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Remove the 2 bolts and park/neutral position switch assembly from the automatic transaxle case sub-assembly.
35015S
3.REMOVE REFILL PLUG
Remove the refill plug and gasket from the automatic transaxle case sub-assembly.
35405C
4.REMOVE OVERFLOW PLUG
Using a 10 mm socket hexagon wrench, remove the overflow plug and gasket from the transaxle housing.
35125C
5.REMOVE NO. 1 TRANSMISSION OIL FILLER TUBE
Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the transaxle housing.
32901C
6.REMOVE OIL COOLER UNION SUB-ASSEMBLY
| *1 | Oil Cooler Union Bolt |
Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.
Remove the oil cooler union bolt, 2 gaskets and oil cooler union sub-assembly from the automatic transaxle case sub-assembly.
32922D
7.REMOVE OIL COOLER OUTLET UNION OR ELBOW
Using a 19 mm union nut wrench, remove the oil cooler outlet union or elbow from the automatic transaxle case sub-assembly.
Remove the O-ring from the oil cooler outlet union or elbow.
35151F
8.REMOVE TRANSMISSION CASE SIDE COVER
Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.
82125J
9.REMOVE TRANSMISSION WIRE (w/o Stop And Start System)
| *a | Connector (A) |
| *b | Connector (B) |
Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.
Disconnect the 9 solenoid valve connectors.
Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.
Remove the bolt and temperature sensor clamp and separate the temperature sensor from the transmission valve body assembly.
Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.
Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.
82125J
10.REMOVE TRANSMISSION WIRE (w/ Stop And Start System)
| *a | Connector (A) |
| *b | Connector (B) |
Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.
Disconnect the 9 solenoid valve connectors.
Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.
Disengage the wire harness clamp to disconnect the transmission wire (oil pump with solenoid assembly).
Disconnect the transmission wire connector.
Disengage the clamp to disconnect the transmission wire (oil pump with solenoid assembly) from the solenoid lock plate.
Remove the bolt and temperature sensor clamp and separate the temperature sensor from the transmission valve body assembly.
Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.
Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.
35410
11.REMOVE TRANSMISSION VALVE BODY ASSEMBLY (w/o Stop And Start System)
Disengage the clamp to disconnect the transmission revolution sensor (NC) wire connector.
Remove the 9 bolts and transmission valve body assembly from the automatic transaxle case sub-assembly.
| *1 | Transaxle Case Gasket |
| *2 | No. 1 Front Oil Pump Cover Gasket |
| *3 | No. 2 Front Oil Pump Cover Gasket |
Remove the 2 transaxle case gaskets from the automatic transaxle case sub-assembly.
Remove the transaxle case gasket from the counter drive gear sub-assembly.
Remove the No. 1 front oil pump cover gasket from the front oil pump assembly.
Remove the No. 2 front oil pump cover gasket from the front oil pump assembly.
35410
12.REMOVE TRANSMISSION VALVE BODY ASSEMBLY (w/ Stop And Start System)
Disengage the clamp to disconnect the transmission revolution sensor (NC) wire connector.
Remove the 9 bolts and transmission valve body assembly from the automatic transaxle case sub-assembly.
| *1 | Transaxle Case Gasket |
| *2 | No. 1 Front Oil Pump Cover Gasket |
| *3 | No. 2 Front Oil Pump Cover Gasket |
Remove the 2 transaxle case gaskets from the automatic transaxle case sub-assembly.
Remove the transaxle case gasket from the counter drive gear sub-assembly.
Remove the transaxle case gasket from the front oil pump assembly.
Remove the No. 1 front oil pump cover gasket from the front oil pump assembly.
Remove the No. 2 front oil pump cover gasket from the front oil pump assembly.
89413N
13.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
Remove the bolt and transmission revolution sensor (NT) from the automatic transaxle case sub-assembly.
89413S
14.REMOVE TRANSMISSION REVOLUTION SENSOR (NC)
Remove the bolt and transmission revolution sensor (NC) from the counter drive gear sub-assembly.
15.INSPECT INPUT SHAFT END PLAY
35111C
16.REMOVE TRANSAXLE HOUSING
Remove the 21 bolts.
Using a plastic hammer, tap on the circumference of the transaxle housing to remove it from the automatic transaxle case sub-assembly.
| *1 | Transaxle Case Gasket |
| *2 | O-ring |
Remove the 5 transaxle case gaskets from the front oil pump assembly.
Remove the O-ring from the automatic transaxle case sub-assembly.
35174
17.REMOVE TRANSAXLE HOUSING OIL SEPARATOR
Remove the 3 bolts and transaxle housing oil separator from the transaxle housing.
35394
18.REMOVE TRANSMISSION OIL CLEANER MAGNET
Remove the 3 transmission oil cleaner magnets from the transaxle housing oil separator.
35394
19.INSPECT TRANSMISSION OIL CLEANER MAGNET
35882C
20.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE
Remove the differential gear lube apply tube from the transaxle housing.
35847C
21.REMOVE TRANSMISSION LUBE APPLY TUBE
Remove the bolt and clamp from the transaxle housing.
Remove the transmission lube apply tube from the transaxle housing.
22.REMOVE DIFFERENTIAL CASE ASSEMBLY
Remove the differential case assembly from the automatic transaxle case sub-assembly.
35617
23.REMOVE CLUTCH DRUM OIL SEAL RING
Remove the clutch drum oil seal ring from the front oil pump assembly.
35354
24.REMOVE OIL PUMP SPROCKET FRONT THRUST WASHER
Remove the oil pump sprocket front thrust washer from the transmission oil pump drive sprocket.
35781C
25.REMOVE TRANSMISSION DRIVE CHAIN
Remove the transmission drive chain together with the transmission oil pump drive sprocket and oil pump drive shaft sub-assembly from the front oil pump assembly.
To avoid damaging the bush of the front oil pump assembly, remove the transmission drive chain, transmission oil pump drive sprocket and oil pump drive shaft sub-assembly horizontally relative to the front oil pump assembly.
35355
26.REMOVE OIL PUMP SPROCKET REAR THRUST WASHER
Remove the oil pump sprocket rear thrust washer from the front oil pump assembly.
35409D
27.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY
Remove the bolt and manual detent spring sub-assembly from the front oil pump assembly.
28.REMOVE FRONT OIL PUMP ASSEMBLY
To avoid damaging the front oil pump assembly and transmission valve body assembly, when removing the front oil pump assembly, first remove the transmission valve body assembly.
Remove the 7 bolts and front oil pump assembly from the automatic transaxle case sub-assembly.
35737
29.REMOVE PLANETARY CARRIER THRUST WASHER
Remove the planetary carrier thrust washer from the C-3 and C-4 clutch assembly.
34610
30.REMOVE C-3 AND C-4 CLUTCH ASSEMBLY
Remove the C-3 and C-4 clutch assembly from the front planetary gear assembly.
31.INSPECT CLEARANCE OF C-3 CLUTCH
32.INSPECT CLEARANCE OF C-4 CLUTCH
35738
33.REMOVE NO. 2 PLANETARY CARRIER THRUST WASHER
Remove the No. 2 planetary carrier thrust washer from the front planetary gear assembly.
35719B
34.REMOVE PLANETARY SUN GEAR
Remove the planetary sun gear from the front planetary gear assembly.
35779A
35.REMOVE NO. 9 THRUST BEARING RACE
Remove the No. 9 thrust bearing race from the front planetary gear assembly.
36.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the front planetary gear assembly.
35778
37.REMOVE NO. 8 THRUST BEARING RACE
Remove the No. 8 thrust bearing race from the front planetary gear assembly.
35720
38.REMOVE FRONT PLANETARY GEAR ASSEMBLY
Remove the front planetary gear assembly from the front planetary ring gear.
39.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the front planetary ring gear.
35777
40.REMOVE NO. 7 THRUST BEARING RACE
Remove the No. 7 thrust bearing race from the front planetary gear assembly.
35720
41.INSPECT FRONT PLANETARY GEAR ASSEMBLY
35712E
42.REMOVE INPUT SHAFT OIL SEAL RING
Remove the 5 input shaft oil seal rings from the front planetary gear assembly.
35749B
43.REMOVE REAR INPUT SHAFT OIL SEAL RING
Remove the 2 rear input shaft oil seal rings from the front planetary gear assembly.
35743
44.REMOVE FRONT PLANETARY RING GEAR
Remove the front planetary ring gear with front planetary ring gear flange from the C-1 clutch assembly.
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front planetary ring gear.
Be careful not to damage the front planetary ring gear and front planetary ring gear flange.
Remove the front planetary ring gear flange from the front planetary ring gear.
45.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the C-1 clutch assembly.
35776
46.REMOVE NO. 6 THRUST BEARING RACE
Remove the No. 6 thrust bearing race from the C-1 clutch assembly.
47.REMOVE C-1 CLUTCH ASSEMBLY
Remove the C-1 clutch assembly from the sun gear input hub sub-assembly.
48.INSPECT CLEARANCE OF C-1 CLUTCH
35633
49.REMOVE FRONT CLUTCH CLUTCH DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the clutch drum sub-assembly.
Be careful not to damage the clutch drum sub-assembly.
| *1 | Forward Clutch Flange |
| *2 | Front Clutch Clutch Disc |
| *3 | Forward Multiple Disc Clutch Clutch Plate |
| *a | Snap Ring Side |
| *b | Front Clutch Clutch Disc Side |
Remove the forward clutch flange, 5 front clutch clutch discs and 5 forward multiple disc clutch clutch plates from the clutch drum sub-assembly.
35633
50.INSPECT FRONT CLUTCH CLUTCH DISC
35668
51.REMOVE NO. 1 CLUTCH BALANCER
Place SST on the No. 1 clutch balancer and compress the rear clutch piston return compression spring with a press.
Do not compress the rear clutch piston return compression spring excessively.
Using SST, remove the snap ring from the clutch drum sub-assembly.
Remove the No. 1 clutch balancer from the forward clutch piston.
35650B
52.REMOVE REAR CLUTCH PISTON RETURN COMPRESSION SPRING
Remove the rear clutch piston return compression spring from the forward clutch piston.
35612B
53.REMOVE FORWARD CLUTCH PISTON
Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the ATF hole of the clutch drum sub-assembly to remove the forward clutch piston from the clutch drum sub-assembly.
Applying compressed air may cause the forward clutch piston to jump out. When removing the forward clutch piston, hold it by hand using a piece of cloth.
Be careful as ATF may spray when applying compressed air.
Remove the O-ring from the clutch drum sub-assembly.
Remove the D-ring from the clutch drum sub-assembly.
35606M
54.REMOVE SUN GEAR INPUT HUB SUB-ASSEMBLY
Remove the sun gear input hub sub-assembly from the counter drive gear sub-assembly.
55.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the sun gear input hub sub-assembly.
35775K
56.REMOVE NO. 5 THRUST BEARING RACE
Remove the No. 5 thrust bearing race from the sun gear input hub sub-assembly.
35506
57.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY
Remove the bolt.
Align the cutouts of the manual valve lever sub-assembly and manual valve lever shaft sub-assembly, and remove the manual valve lever shaft sub-assembly.
Rotating the manual valve lever shaft sub-assembly to the area shown in the illustration will align the cutouts.
Remove the O-ring from the manual valve lever shaft sub-assembly.
35505
58.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY
Remove the manual valve lever sub-assembly from the automatic transaxle case sub-assembly.
35596
59.REMOVE PAWL STOPPER PLATE
Remove the 2 bolts and pawl stopper plate from the automatic transaxle case sub-assembly.
35506J
60.REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING
Remove the manual valve lever shaft retainer spring from the automatic transaxle case sub-assembly.
35501
61.REMOVE PARKING LOCK ROD SUB-ASSEMBLY
| *1 | Manual Valve Lever Shaft Sub-assembly |
| *2 | Parking Lock Rod Sub-assembly |
Move the manual valve lever shaft sub-assembly and parking lock rod sub-assembly as shown in the illustration, and remove the parking lock rod sub-assembly.
Align the cutouts of the parking lock rod sub-assembly and manual valve lever shaft sub-assembly and remove the parking lock rod sub-assembly.
35506
62.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY
Remove the manual valve lever shaft sub-assembly from the automatic transaxle case sub-assembly.
35557A
63.REMOVE PARKING LOCK PAWL TORSION SPRING
Remove the parking lock pawl torsion spring from the automatic transaxle case sub-assembly.
35556
64.REMOVE PARKING LOCK PAWL SHAFT
Remove the parking lock pawl shaft from the automatic transaxle case sub-assembly.
35557
65.REMOVE PARKING LOCK PAWL
Remove the parking lock pawl from the automatic transaxle case sub-assembly.
35598
66.REMOVE PARKING LOCK SLEEVE
Remove the parking lock sleeve from the automatic transaxle case sub-assembly.
67.INSPECT CLEARANCE OF B-1 BRAKE
35704C
68.REMOVE COUNTER DRIVE GEAR SUB-ASSEMBLY
| *a | Bolt (A) |
| *b | Bolt (B) |
Using a T50 "TORX" socket wrench, remove the 2 bolts (A) from the counter drive gear sub-assembly.
Remove the 6 bolts (B) from the counter drive gear sub-assembly.
Remove the counter drive gear sub-assembly together with the pinion and counter driven gear sub-assembly from the automatic transaxle case sub-assembly.
Remove the O-ring from the automatic transaxle case sub-assembly.
35681C
69.REMOVE NO. 1 BRAKE DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the counter drive gear sub-assembly.
Be careful not to damage the counter drive gear sub-assembly.
| *1 | No. 1 Brake Flange |
| *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate |
| *a | Snap Ring Side |
| *b | No. 1 Brake Disc Side |
Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the counter drive gear sub-assembly.
35681C
70.INSPECT NO. 1 BRAKE DISC
35739
71.REMOVE NO. 3 PLANETARY CARRIER THRUST WASHER
Remove the No. 3 planetary carrier thrust washer from the rear planetary gear assembly.
35706V
72.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY
Remove the planetary sun gear sub-assembly from the rear planetary gear assembly.
35706V
73.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY
35707D
74.REMOVE REAR PLANETARY SUN GEAR SUB-ASSEMBLY
Remove the rear planetary sun gear sub-assembly from the C-2 clutch assembly.
35760
75.REMOVE REAR PLANETARY GEAR ASSEMBLY
Remove the rear planetary gear assembly from the C-2 clutch assembly.
35729B
76.REMOVE NO. 4 PLANETARY CARRIER THRUST WASHER
Remove the No. 4 planetary carrier thrust washer from the rear planetary gear assembly.
35760
77.INSPECT REAR PLANETARY GEAR ASSEMBLY
35785B
78.REMOVE NO. 4 THRUST BEARING RACE
Remove the No. 4 thrust bearing race from the rear planetary sun gear sub-assembly.
79.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the rear planetary sun gear sub-assembly.
35789U
80.REMOVE THRUST BEARING RACE
Remove the thrust bearing race from the rear planetary sun gear sub-assembly.
35788D
81.REMOVE NO. 3 THRUST BEARING RACE
Remove the No. 3 thrust bearing race from the rear planetary sun gear sub-assembly.
35707D
82.INSPECT REAR PLANETARY SUN GEAR SUB-ASSEMBLY
83.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the C-2 clutch assembly.
35787C
84.REMOVE NO. 2 THRUST BEARING RACE
Remove the No. 2 thrust bearing race from the C-2 clutch assembly.
85.INSPECT CLEARANCE OF C-2 CLUTCH
86.REMOVE C-2 CLUTCH ASSEMBLY
Remove the C-2 clutch assembly from the automatic transaxle case sub-assembly.
87.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the C-2 clutch assembly.
35786A
88.REMOVE NO. 1 THRUST BEARING RACE
Remove the No. 1 thrust bearing race from the automatic transaxle case sub-assembly.
35667B
89.REMOVE NO. 2 CLUTCH DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the intermediate shaft sub-assembly.
Be careful not to damage the intermediate shaft sub-assembly.
| *1 | Direct Clutch Flange |
| *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Plate |
| *a | Snap Ring Side |
| *b | No. 2 Clutch Disc Side |
Remove the direct clutch flange, 4 No. 2 clutch discs and 4 No. 2 clutch plates from the intermediate shaft sub-assembly.
35667B
90.INSPECT NO. 2 CLUTCH DISC
35698A
91.REMOVE C-2 CLUTCH BALANCER
Place SST on the C-2 clutch balancer and compress the clutch return spring sub-assembly with a press.
Do not compress the clutch return spring sub-assembly excessively.
Using SST, remove the snap ring from the intermediate shaft sub-assembly.
Remove the C-2 clutch balancer from the intermediate shaft sub-assembly.
35608N
92.REMOVE CLUTCH RETURN SPRING SUB-ASSEMBLY
Remove the clutch return spring sub-assembly from the intermediate shaft sub-assembly.
35608N
93.INSPECT CLUTCH RETURN SPRING SUB-ASSEMBLY
35652E
94.REMOVE C-2 CLUTCH PISTON
Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the ATF hole of the intermediate shaft sub-assembly.
Applying compressed air may cause the C-2 clutch piston to jump out. When removing the C-2 clutch piston, hold it by hand using a piece of cloth.
Be careful as ATF may spray when applying compressed air.
Remove the C-2 clutch piston from the intermediate shaft sub-assembly.
Remove the 2 O-rings from the intermediate shaft sub-assembly.
35653B
95.REMOVE DIRECT CLUTCH DRUM OIL SEAL RING
Remove the 2 direct clutch drum oil seal rings from the automatic transaxle case sub-assembly.
96.INSPECT CLEARANCE OF B-2 BRAKE
35682
97.REMOVE 2ND BRAKE BRAKE DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
| *1 | 2nd Brake Brake Flange |
| *2 | 2nd Brake Brake Disc |
| *3 | 2nd Brake Brake Plate |
| *a | Snap Ring Side |
| *b | 2nd Brake Brake Disc Side |
Remove the 2nd brake brake flange, 5 2nd brake brake discs and 5 2nd brake brake plates from the automatic transaxle case sub-assembly.
35682
98.INSPECT 2ND BRAKE BRAKE DISC
35623P
99.REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON
Remove the No. 2 1st and reverse brake piston from the automatic transaxle case sub-assembly.
35068
100.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.
Do not compress the 1st and reverse brake return spring sub-assembly excessively.
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the automatic transaxle case sub-assembly.
35068
101.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
35623H
102.REMOVE 1ST AND REVERSE BRAKE PISTON
Apply compressed air (approximately 392 kPa (4.0 kgf/cm2, 57 psi)) to the ATF hole to remove the 1st and reverse brake piston from the automatic transaxle case sub-assembly.
Remove the 2 O-rings from the 1st and reverse brake piston.
41206A
103.REMOVE NEEDLE ROLLER BEARING
Using SST, remove the needle roller bearing from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
104.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
Using a screwdriver with its tip wrapped with protective tape, remove the manual valve lever shaft oil seal from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
31105D
105.REMOVE FRONT TRANSAXLE CASE OIL SEAL
Using SST, remove the front transaxle case oil seal from the transaxle housing.
Be careful not to damage the transaxle housing.
31105H
106.REMOVE TRANSAXLE CASE OIL SEAL
Using SST, remove the transaxle case oil seal from the transaxle housing.
Be careful not to damage the transaxle housing.
43420H
107.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
35605C
108.REMOVE NEEDLE ROLLER BEARING
Using SST and a press, remove the needle roller bearing from the transaxle housing.
Be careful not to damage the transaxle housing.
41206A
109.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the counter driven gear rear tapered roller bearing (outer race) from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
Align the claw of SST with the indentation of the automatic transaxle case sub-assembly when removing the parts.
41206A
110.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)
Using SST, remove the counter driven gear rear tapered roller bearing (inner race) from the pinion and counter driven gear sub-assembly.
Because SST is attached to the roller portion, there is a possibility that the roller portion could break and SST could come off before the counter driven gear rear tapered roller bearing (inner race) comes off.
If the roller portion breaks and SST comes off, reattach SST to the inner race in the position shown in the illustration, and continue removing the parts.
41206A
111.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the counter driven gear front tapered roller bearing (outer race) and pinion and counter driven gear shim from the transaxle housing.
Be careful not to damage the transaxle housing.
Align the claw of SST with the indentation of the transaxle housing when removing the parts.
41206A
112.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)
Using SST, remove the counter driven gear front tapered roller bearing (inner race) from the pinion and counter driven gear sub-assembly.
35104Q
113.REMOVE NO. 1 TRANSAXLE CASE PLUG
Remove the 4 No. 1 transaxle case plugs from the automatic transaxle case sub-assembly.
Remove the 4 No. 1 transaxle case plugs from the transaxle housing.
Remove the 8 O-rings from the 8 No. 1 transaxle case plugs.
35104R
114.REMOVE NO. 2 TRANSAXLE CASE PLUG
Using a 6 mm socket hexagon wrench, remove the 3 No. 2 transaxle case plugs and 3 gaskets from the automatic transaxle case sub-assembly.
Using a 6 mm socket hexagon wrench, remove the 3 No. 2 transaxle case plugs and 3 gaskets from the transaxle housing.
35101E
115.REMOVE AUTOMATIC TRANSMISSION CASE STRAIGHT PIN
It is not necessary to remove the automatic transmission case straight pins unless they are being replaced.
Remove the 2 automatic transmission case straight pins from the automatic transaxle case sub-assembly.
35104B
116.REMOVE NO. 1 BREATHER PLUG (ATM)
| *a | Push |
Disengage each claw and remove the No. 1 breather plug (ATM) from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.