Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRILLE SHUTTER › 2020.11–2021.10
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0452911 GRILLE SHUTTER A

EXTERIOR PANELS / TRIM  GRILLE SHUTTER  REASSEMBLY  


PROCEDURE

Hide 53157C 1.INSTALL NO. 3 RADIATOR GRILLE SEAL

a.
B564412

Engage the 3 claws to install the No. 3 radiator grille seal.


Hide 53155J 2.INSTALL NO. 1 RADIATOR GRILLE SEAL

HINT:

When installing the No. 1 radiator grille seal, heat the radiator shutter sub-assembly using a heat light.


Standard Measurement:
Item Measurement
Radiator Shutter Sub-assembly 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the radiator shutter sub-assembly excessively.


a.

Clean the radiator shutter sub-assembly surface.

i.

Using a heat light, heat the radiator shutter sub-assembly surface.


ii.

Remove any remaining double-sided tape from the radiator shutter sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 1 radiator grille seal.

i.

Using a heat light, heat the radiator shutter sub-assembly surface.


ii.

Remove the release paper from the No. 1 radiator grille seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.
B564411

Install the No. 1 radiator grille seal.

NOTICE:
·

If the No. 1 radiator grille seal has been removed, it must be replaced with a new one as it may be deformed or the strength of its adhesive may be deteriorated.

·

Press the No. 1 radiator grille seal firmly to install it.





Hide 53156G 3.INSTALL NO. 2 RADIATOR GRILLE SEAL

HINT:
·

When installing the No. 2 radiator grille seal, heat the radiator shutter sub-assembly using a heat light.

·

Use the same procedure for the RH side and LH side.



Standard Measurement:
Item Measurement
Radiator Shutter Sub-assembly 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the radiator shutter sub-assembly excessively.


a.

Clean the radiator shutter sub-assembly surface.

i.

Using a heat light, heat the radiator shutter sub-assembly surface.


ii.

Remove any remaining double-sided tape from the radiator shutter sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 2 radiator grille seal.

i.

Using a heat light, heat the radiator shutter sub-assembly surface.


ii.

Remove the release paper from the No. 2 radiator grille seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.
B564410

Install the No. 2 radiator grille seal.

NOTICE:
·

If the No. 2 radiator grille seal has been removed, it must be replaced with a new one as it may be deformed or the strength of its adhesive may be deteriorated.

·

Press the No. 2 radiator grille seal firmly to install it.





Hide 88940D 4.INSTALL SWING GRILLE ACTUATOR ASSEMBLY

a.
B564409C01
0,0 0,0 false
V113147

Install in this Direction


Install the swing grille actuator assembly as shown in the illustration.


b.
B564407

Connect the connector.


Hide 85667F 5.INSTALL MOTOR COVER

a.
B566977C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the motor cover as shown in the illustration.