Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model with Manual Air Conditioning System) › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0453069 AIR CONDITIONING SYSTEM(for Gasoline Model with Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model with Manual Air Conditioning System)  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly.

If the airflow volume is low or the blower speed cannot be changed, the following factors may be the cause.

Symptom Factor
Airflow volume cannot be changed
·

Air conditioning amplifier assembly malfunction

·

Rear blower motor with fan sub-assembly malfunction

·

Harness or connector



WIRING DIAGRAM

E432295E02
2.229,4.667 3.635,5.083 1.406,0.417 10 false Rear Blower Motor with Fan Sub-assembly 4.688,4.5 6.24,4.854 1.552,0.354 10 false Air Conditioning Amplifier Assembly 2.292,3.146 3.448,3.51 1.156,0.365 10 false Rear Blower Motor Control 2.229,4.49 2.688,4.688 0.458,0.198 10 false M13 4.479,1.927 4.938,2.125 0.458,0.198 10 false H64 2.292,2.99 2.75,3.188 0.458,0.198 10 false M14 4.885,1.917 5.5,2.115 0.615,0.198 10 false SBLW 4.521,1.729 4.833,1.927 0.313,0.198 10 false 10 3.448,1.802 3.76,2 0.313,0.198 10 false 3 3.219,1.927 3.531,2.125 0.313,0.198 10 false SI 2.51,2.573 2.823,2.771 0.313,0.198 10 false VM 3.063,2.573 3.5,2.792 0.438,0.219 10 false GND 2.51,1.917 2.823,2.115 0.313,0.198 10 false +B 2.323,1.813 2.635,2.01 0.313,0.198 10 false 1 2.323,2.438 2.635,2.635 0.313,0.198 10 false 2 3.448,2.438 3.76,2.635 0.313,0.198 10 false 6 2.677,0.854 3.354,1.167 0.677,0.313 10 false A/C RR 4.115,0.688 6.406,0.885 2.292,0.198 10 false from ALT Fuse 2.323,4.052 2.635,4.25 0.313,0.198 10 false 2 3.458,4.052 3.771,4.25 0.313,0.198 10 false 1 2.51,4.167 2.667,4.365 0.156,0.198 10 false + 3.281,4.156 3.438,4.354 0.156,0.198 10 false - 4.49,3.323 4.948,3.521 0.458,0.198 10 false H64 4.573,3.115 4.885,3.313 0.313,0.198 10 false 4 4.885,3.313 5.5,3.51 0.615,0.198 10 false GND2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (REAR BLOWER MOTOR)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Blower Motor Rear blower motor with fan sub-assembly Min.: 0
Max.: 31
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Blower Motor
50004 121 35

Result:
Result Proceed to
Rear blower motor with fan sub-assembly does not operate A
Rear blower motor with fan sub-assembly operates but does not change speed B



A

2.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - POWER SOURCE AND BODY GROUND)

B

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - POWER SOURCE AND BODY GROUND)
a.
E432381C02
1.417,0.135 1.917,0.385 0.5,0.25 1.938,1.313 2.188,0.979 2.188,0.979 2.438,0.979 true 1.385,1.052 1.135,0.719 1.135,0.719 0.885,0.719 true 0.75,0.156 1.063,0.354 0.313,0.198 10 false *a 0.656,0.635 0.969,0.833 0.313,0.198 10 false +B 2.479,0.896 2.865,1.104 0.385,0.208 10 false GND 1.542,0.188 1.854,0.385 0.313,0.198 10 false M14
*a Front view of wire harness connector
(to Rear Blower Motor Control)


Disconnect the M14 rear blower motor control connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M14-1 (+B) - Body ground Ignition switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
M14-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY - REAR BLOWER MOTOR CONTROL AND BODY GROUND)

NG

REPLACE REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY - REAR BLOWER MOTOR CONTROL AND BODY GROUND)
a.

Disconnect the M14 rear blower motor control connector.


b.

Disconnect the M13 rear blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-2 (+) - M14-2 (VM) Always Below 1 Ω
M13-1 (-) - Body ground Always Below 1 Ω
M13-2 (+) or M14-2 (VM) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the M14 rear blower motor control connector.


b.

Disconnect the H64 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-3 (SI) - H64-10 (SBLW) Always Below 1 Ω
M14-3 (SI) or H64-10 (SBLW) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Connect the M14 rear blower motor control connector.


b.

Connect the M13 rear blower motor with fan sub-assembly connector.


c.

Connect the H64 air conditioning amplifier assembly connector.


d.

Using an oscilloscope, check the waveform.

E432383C01
2.26,0.135 2.677,0.396 0.417,0.26 1.813,1.927 1.927,0.927 true 2.75,1.927 2.573,1.073 true 2.354,0.188 2.813,0.385 0.458,0.198 10 false H64 1.781,0.156 2.094,0.354 0.313,0.198 10 false *a 4.677,2.969 5.135,3.167 0.458,0.198 10 false GND 2.604,1.958 3.063,2.156 0.458,0.198 10 false SBLW 1.635,1.958 2.125,2.167 0.49,0.208 10 false GND2
*a Component with harness connected
(Air Conditioning Amplifier Assembly)
- -


Item Content
Terminal No. H64-10 (SBLW) - H64-4 (GND2)
Tool Setting 2 V/DIV., 1 ms./DIV.
Condition
·

Ignition switch ON

·

Blower speed: LO



OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY