Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0453179 TOYOTA MULTI OPERATION TOUCH SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the integration control sub-assembly.

WIRING DIAGRAM

E444863E05
1.719,0.604 3.552,0.802 1.833,0.198 10 false from Auxiliary Battery 1.729,2.5 3.396,2.719 1.667,0.219 10 false from IG1-NO. 1 Relay 3.677,0.813 4.615,1.01 0.938,0.198 10 false ECU-B NO. 2 3.615,2.677 4.688,2.875 1.073,0.198 10 false ECU-IG1 NO. 4 3.781,1.74 4.875,2 1.094,0.26 10 false ECU-ACC 5.021,3.719 5.333,3.917 0.313,0.198 10 false H8 5.052,0.542 5.208,0.74 0.156,0.198 10 false 1 5.042,1.479 5.354,1.677 0.313,0.198 10 false 3 5.042,2.396 5.354,2.594 0.313,0.198 10 false 4 4.99,3.177 5.24,3.406 0.25,0.229 10 false 20 5.24,0.646 5.698,0.844 0.458,0.198 10 false B 5.25,1.573 5.865,1.771 0.615,0.198 10 false ACC 5.25,2.5 5.563,2.698 0.313,0.198 10 false IG+ 5.24,3.292 5.854,3.49 0.615,0.198 10 false GND 5.021,3.885 6.198,4.448 1.177,0.563 10 false Integration Control Sub-assembly 2.042,1.563 3.875,1.76 1.833,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBY POWER SOURCE)
a.

Disconnect the H8 integration control sub-assembly connector.


b.
E432157C04
1.5,0.25 1.917,0.5 0.417,0.25 0.823,0.979 0.823,0.479 0.823,0.479 0.99,0.479 true 0.719,0.969 0.719,0.219 0.719,0.219 0.885,0.219 true 0.469,0.99 0.469,0.49 0.469,0.49 0.302,0.49 true 0.635,1.208 0.635,1.792 0.635,1.792 0.469,1.792 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 0.135,1.708 0.594,1.927 0.458,0.219 10 false GND 0.146,0.406 0.604,0.625 0.458,0.219 10 false B 0.948,0.135 1.406,0.354 0.458,0.219 10 false ACC 1.063,0.396 1.521,0.615 0.458,0.219 10 false IG+ 1.604,0.292 2.063,0.51 0.458,0.219 10 false H8
*a Front view of wire harness connector
(to Integration Control Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-20 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H8-1 (B) - H8-20 (GND) Ignition switch off 11 to 14 V
H8-3 (ACC) - H8-20 (GND) Ignition switch ACC 11 to 14 V
G3-4 (IG+) - H8-20 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR