Wear protective gloves. Sharp areas on the seat frame may injure your hands.
71016A
1.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Install the rear seat cushion frame sub-assembly LH with the 4 nuts.
72134A
2.INSTALL FRONT INNER SEAT TRACK UPPER RAIL BRACKET LH
Install the front inner seat track upper rail bracket LH with the 2 nuts.
71018
3.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH
|
Install in this Direction |
Temporarily install the rear seatback frame sub-assembly LH to the No. 1 seat cushion frame sub-assembly LH as shown in the illustration.
Temporarily install the 4 bolts.
Tighten the 4 bolts while pulling the rear seatback frame sub-assembly LH as shown in the illustration.
72308D
4.INSTALL NO. 2 RECLINING CONTROL LINK SUB-ASSEMBLY LH
Install the No. 2 reclining control link sub-assembly LH with the 2 nuts.
72308C
5.INSTALL NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY LH
Install the No. 1 reclining control link sub-assembly LH with the 2 nuts.
72704A
6.INSTALL REAR SEAT RECLINING CONTROL CABLE
Route the rear seat reclining control cable as shown in the illustration and engage the clamp.
Engage the 10 clamps and cable clamp to install the rear seat reclining control cable.
72210H
7.INSTALL REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY LH
Route the rear No. 1 seat track control cable assembly LH as shown in the illustration and engage the 2 clamps.
|
Clamp |
|
Wire Harness Clamp |
Install the rear No. 1 seat track control cable assembly LH with the 2 wire harness clamps.
8.INSTALL CONNECTOR MALE HOUSING (w/o Seat Heater System)
w/o Seat Belt Warning System:
Engage the clamp to install the connector male housing.
82194
9.INSTALL REAR SEAT WIRE LH (w/o Seat Heater System)
Engage the 7 clamps to install the rear seat wire LH.
82194
10.INSTALL REAR SEAT WIRE LH (w/ Seat Heater System)
w/o Seat Belt Warning System:
Engage the 7 clamps to install the rear seat wire LH.
w/ Seat Belt Warning System:
Engage the 8 clamps to install the rear seat wire LH.
71691P
11.INSTALL REAR NO. 2 SEAT CUSHION HINGE UPPER COVER RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the claw and guide as shown in the illustration to install the rear No. 2 seat cushion hinge upper cover RH.
71692M
12.INSTALL REAR NO. 2 SEAT CUSHION HINGE UPPER COVER LH
|
Install in this Direction |
Engage the claw and guide as shown in the illustration to install the rear No. 2 seat cushion hinge upper cover LH.
72552A
13.INSTALL RECLINING HINGE COVER LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the clip and 4 claws as shown in the illustration to install the reclining hinge cover LH.
71834A
14.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
|
Install in this Direction |
Engage the claw and guide as shown in the illustration to install the rear No. 1 seat reclining cover LH.
73480A
15.INSTALL REAR SEAT INNER BELT ASSEMBLY LH
71639
16.INSTALL REAR SEAT CUSHION HINGE COVER LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 3 claws as shown in the illustration to install the rear seat cushion hinge cover LH.
71833A
17.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
|
Install in this Direction |
Engage the claw and guide as shown in the illustration to install the rear No. 1 seat reclining cover RH.
71829B
18.INSTALL REAR SEAT CUSHION REAR MOULDING LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 6 claws and 8 guides as shown in the illustration to install the rear seat cushion rear moulding LH.
72598C
19.INSTALL RECLINING REMOTE CONTROL BEZEL LH
Engage the 2 claws and guide to install the reclining remote control bezel LH.
87510S
20.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)
71078S
21.INSTALL SEPARATE TYPE REAR SEATBACK COVER
When installing a separate type rear seatback cover, refer to precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the 6 claws to install the separate type rear seatback cover to the separate type rear seatback pad LH.
Be careful not to damage the separate type rear seatback cover.
22.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD
Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.
Engage the hook.
|
Install in this Direction |
Engage the 4 claws as shown in the illustration to install the 2 rear seat headrest supports.
71702C
23.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
| *a | Clip |
| *b | Cable |
Engage the rear seat reclining control cable as shown in the illustration.
Make sure to route the cable as shown in the illustration.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 2 guides as shown in the illustration.
Engage the 6 clips and 2 claws as shown in the illustration to install the rear seatback board sub-assembly LH.
Engage the hook.
|
Fastener |
Close the 2 fasteners as shown in the illustration.
72997
24.INSTALL REAR SEATBACK COVER LH
|
Install in this Direction |
Engage the 6 claws as shown in the illustration to install the rear seatback cover LH.
Engage the 2 claws as shown in the illustration.
72054C
25.INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH
Connect the rear seat reclining control cable.
|
Install in this Direction |
Engage the guide as shown in the illustration.
Install the reclining remote control lever sub-assembly LH with the 2 screws.
72616A
26.INSTALL REAR SEATBACK LOCK STRIKER COVER LH
|
Install in this Direction |
Engage the 2 guides and claw as shown in the illustration to install the rear seatback lock striker cover LH.
87501F
27.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
Engage the clamp to install the seat heater control sub-assembly LH.
Connect the connector.
87510Q
28.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)
71076S
29.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
When installing a separate type rear seat cushion cover, refer to precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the 14 claws.
Be careful not to damage the separate type rear seat cushion cover.
|
Fastener |
Engage the 5 fasteners to install the separate type rear seat cushion cover.
30.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Temporarily install the separate type rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly LH.
Engage the 6 hooks.
Engage the hook.
Engage the 2 hooks.
w/ Seat Heater System:
Engage the 2 clamps.
Connect the 2 connectors.
w/ Occupant Detection Sensor:
Engage the clamp.
Connect the connector.
Engage the clamp.
Engage the 3 hooks.
Engage the 2 hooks to install the separate type rear seat cushion cover with pad.
71826B
31.INSTALL REAR SEAT CUSHION MOULDING LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 5 claws, clip and 14 guides as shown in the illustration to install the rear seat cushion moulding LH.
72058E
32.INSTALL REAR SEAT NO. 2 LOCK CONTROL LEVER SUB-ASSEMBLY LH
Connect the rear No. 1 seat track control cable assembly LH.
Engage the 2 guides.
Install the rear seat No. 2 lock control lever sub-assembly LH with the 2 screws.
72058D
33.INSTALL REAR SEAT NO. 1 LOCK CONTROL LEVER SUB-ASSEMBLY LH
Connect the rear seat reclining control cable.
Engage the 2 guides.
Install the rear seat No. 1 lock control lever sub-assembly LH with the 2 screws.
71849D
34.INSTALL SEAT ADJUSTER COVER CAP LH
Engage the 2 guides and 2 claws to install the rear seat adjuster cover cap LH.
72928
35.INSTALL REAR SEAT CUSHION UNDER COVER LH
Engage the claw, clip and guide to install the rear seat cushion under cover LH.
72526E
36.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
|
Install in this Direction |
Engage the claw as shown in the illustration to install the reclining adjuster release handle LH.
71848K
37.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.