Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0453775 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P056014  System Voltage Circuit Short to Ground or Open  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, the stored ECM data will be cleared and the ECM will determine that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open ECM back-up power source circuit voltage is low for 3 seconds or more (1-trip detection logic).
·

Back-up power source circuit

·

Battery terminals

·

Battery

·

ECM


Comes on DTC stored SAE Code:
P0562

HINT:

If DTC P056014 is stored, the ECM will not store other DTCs.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Wait for 3 seconds or more with the ignition switch ON.

5.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

6.

Input the DTC: P056014.

7.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C380272E05
1.156,2.302 2.229,2.5 1.073,0.198 10 false Battery 1.833,1.271 2.906,1.469 1.073,0.198 10 false FL MAIN 2.917,1.271 5.063,1.469 2.146,0.198 10 false EFI NO. 1 5.573,0.99 6.646,1.188 1.073,0.198 10 false BATT 5.583,2.344 6.656,2.542 1.073,0.198 10 false E1 5.958,3.198 6.5,3.406 0.542,0.208 10 false ECM 5.219,2.344 6.292,2.542 1.073,0.198 10 false C54 5.219,1.115 6.292,1.313 1.073,0.198 10 false A28 5.292,0.896 6.365,1.094 1.073,0.198 10 false 1 5.26,2.135 6.333,2.333 1.073,0.198 10 false 53

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



PROCEDURE

1.INSPECT BATTERY
a.

Check that the battery is not depleted.

Click herePower Source / Network>2GR-FKS (BATTERY / CHARGING)>CHARGING SYSTEM (w/ Stop And Start System)>ON-VEHICLE INSPECTION

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

CHARGE OR REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
C380522C06
1.677,0.052 2.094,0.302 0.417,0.25 0.719,1.896 1.125,0.885 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.771,0.094 2.229,0.292 0.458,0.198 10 false A28 0.406,1.927 1.635,2.125 1.229,0.198 10 false 1 (BATT)
*a Front view of wire harness connector
(to ECM)


Disconnect the A28 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Turn the ignition switch to ON.


d.

Wait 5 seconds or more.


e.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373
Result:
Result Proceed to
DTC P056014 is output A
DTCs are not output B




A

5.REPLACE ECM

B

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT