Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0453775 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P275612  Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery  


DESCRIPTION

The ECM controls the solenoid (SLU) valve using a predetermined current, and performs lock-up and flex lock-up control.

C361130C02
4.833,1.667 4.083,0.75 4.083,0.75 3.917,0.75 true 5,1.917 4.5,2.5 4.5,2.5 4.333,2.5 true 6.083,1.417 5.417,2.833 5.417,2.833 6.083,2 true 1.917,2.813 2.99,3.01 1.073,0.198 10 false *a 0.708,2.104 1.302,2.521 0.594,0.417 10 false *b 5.323,2.865 5.917,3.156 0.594,0.292 10 false *3 4.146,2.427 5.063,2.625 0.917,0.198 10 false *2 3.729,0.667 5.417,0.865 1.688,0.198 10 false *1
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Current *b Hydraulic Pressure


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P275612 Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery While the vehicle is being driven, a short to +B is detected in the solenoid (SLU) valve circuit for 1 second (1-trip detection logic).
·

Solenoid (SLU) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P2763

MONITOR DESCRIPTION

When a short to +B in the solenoid (SLU) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Start the engine.

5.

Perform the Lock-up Function inspection in Road Test.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

6.

Stop the vehicle.

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: P275612.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C361128E31
1.49,1.729 5.156,1.927 3.667,0.198 10 false Solenoid (SLU) Valve 1.063,1.313 1.219,1.51 0.156,0.198 10 false 1 1.083,2.135 1.229,2.427 0.146,0.292 10 false 2 3.427,1.115 4.042,1.313 0.615,0.198 10 false SLU+ 3.458,2.083 4.073,2.281 0.615,0.198 10 false SLU- 5.188,1.115 5.802,1.313 0.615,0.198 10 false SLU+ 5.198,2.083 5.813,2.281 0.615,0.198 10 false SLU- 1.833,2.813 4.438,3.01 2.604,0.198 10 false Transmission Wire 5.583,3.146 6.042,3.344 0.458,0.198 10 false ECM 5.583,2.99 6.042,3.188 0.458,0.198 10 false C54 1.833,2.635 2.292,2.833 0.458,0.198 10 false C51 4.885,1.115 5.198,1.313 0.313,0.198 10 false 76 4.896,2.083 5.208,2.281 0.313,0.198 10 false 61 3.927,1.125 4.24,1.323 0.313,0.198 10 false 5 3.927,2.083 4.24,2.281 0.313,0.198 10 false 4 5.781,0.781 6.396,0.979 0.615,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLU) VALVE) - ECM)
a.

Disconnect the C54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-76 (SLU+) or C54-61 (SLU-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C51 transmission wire connector.


b.

Disconnect the C54 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C51-5 (SLU+) or C54-76 (SLU+) - Other terminals Always 10 kΩ or higher
C51-4 (SLU-) or C54-61 (SLU-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SLU) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.INSPECT SOLENOID (SLU) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLU) Valve)


Remove the solenoid (SLU) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLU) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes operating sound.



Result:
Proceed to
OK
NG



OK

NG