Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor

·

Stop and start system*



*: w/ Stop and Start System

WIRING DIAGRAM

E432787E03
5.552,2.677 6.948,2.917 1.396,0.24 10 false Parking Assist ECU 3.406,2.667 3.958,2.906 0.552,0.24 10 false H57 3.406,2.854 4.49,3.104 1.083,0.25 10 false Steering Sensor 3.479,2.208 3.854,2.406 0.375,0.198 10 false ESS 3.479,1.104 3.854,1.302 0.375,0.198 10 false IG1 3.479,0.552 3.854,0.75 0.375,0.198 10 false BAT 2.083,0.698 3.167,0.948 1.083,0.25 10 false ECU-DCC NO. 1 2.052,1.26 3.135,1.51 1.083,0.25 10 false ECU-IG1 NO. 2 0.25,1.104 1.771,1.365 1.521,0.26 10 false from IG1-NO. 1 Relay*1 0.365,0.521 2.042,0.792 1.677,0.271 10 false from Auxiliary Battery 0.833,3.354 3.135,3.74 2.302,0.385 10 false : CAN Communication Line 3.271,0.427 3.51,0.656 0.24,0.229 10 false 4 3.26,0.979 3.5,1.208 0.24,0.229 10 false 9 3.25,2.083 3.49,2.313 0.24,0.229 10 false 6 0.052,1.656 1.844,1.948 1.792,0.292 10 false from Stop and Start ECU*2 0.156,2.542 3.073,2.854 2.917,0.313 10 false *1: w/o Stop and Start System, for HV Model 0.167,2.917 2.615,3.115 2.448,0.198 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first check that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "!" is displayed on the radio and display receiver assembly or multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the H57 steering sensor connector.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-6 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-9 (IG1) - H57-6 (ESS) Ignition switch ON 11 to 14 V*1,*3
10.5 to 16 V*2
H57-4 (BAT) - H57-6 (ESS) Ignition switch off*1 11 to 14 V
Always*2


*1: for HV Model

*2: for Gasoline Model with Stop and Start System

*3: for Gasoline Model without Stop and Start System



Result:
Result Proceed to
OK A
NG (for HV Model, for Gasoline Model without Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C