Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1682  Front Camera Current Malfunction  


DESCRIPTION

DTC C1682 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1682 Front Camera Current Malfunction Open or short in the front television camera signal circuit
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E372777E17
1.51,0.698 2.427,0.896 0.917,0.198 10 false BCB+ 1.49,1.188 2.406,1.385 0.917,0.198 10 false BGND 5.271,0.708 6.188,0.906 0.917,0.198 10 false BCB+ 5.292,1.177 6.208,1.375 0.917,0.198 10 false BGND 5.073,1.719 5.99,1.917 0.917,0.198 10 false H19 5.073,1.875 6.438,2.104 1.365,0.229 10 false Parking Assist ECU 0.542,1.688 1.458,1.885 0.917,0.198 10 false B5 0.542,1.854 3.24,2.083 2.698,0.229 10 false Front Television Camera Assembly 1.979,0.594 2.375,0.833 0.396,0.24 10 false 6 1.979,1.073 2.375,1.313 0.396,0.24 10 false 5 5.01,0.594 5.406,0.833 0.396,0.24 10 false 15 5.021,1.083 5.417,1.323 0.396,0.24 10 false 37

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly or multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H19 parking assist ECU connector.


b.

Disconnect the B5 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-15 (BCB+) - B5-6 (BCB+) Always Below 1 Ω
H19-37 (BGND) - B5-5 (BGND) Always Below 1 Ω
H19-15 (BCB+) or B5-6 (BCB+) - Body ground Always 10 kΩ or higher
H19-37 (BGND) or B5-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E402272C15
1.417,0.25 1.917,0.5 0.5,0.25 0.5,1.771 0.677,1.771 0.677,1.771 1.094,1.156 true 0.667,0.333 0.833,0.333 0.833,0.333 1.063,0.99 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.302,0.271 0.698,0.427 0.396,0.156 10 false BCB+ 0.094,1.719 0.656,1.875 0.563,0.156 10 false BGND 1.51,0.302 2.01,0.458 0.5,0.156 10 false H19
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-37 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-15 (BCB+) - H19-37 (BGND) Ignition switch ON 5.5 to 7.05 V
H19-15 (BCB+) - H19-37 (BGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG