HYBRID VEHICLE CONTROL ECU
| Terminal No.
(Symbol) |
Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A31-2 (R) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in R | 6.0 to 14 V |
| Ignition switch ON, shift lever not in R | 0 to 1.5 V | ||
| A31-3 (DB1) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in D or S | 6.0 to 14 V |
| Ignition switch ON, shift lever not in D or S | 0 to 1.5 V | ||
| A31-4 (HMCH) - H67-3 (E1) | Communication signal | Ignition switch ON | Pulse generation
(Waveform 1) |
| A31-5 (MREL) - H67-3 (E1) | Main relay | Ignition switch ON | 11 to 14 V |
| A31-6 (HSDN) - H67-3 (E1) | MG ECU shutdown signal | Ignition switch ON (READY) | 0 to 1.5 V |
| A31-7 (STP) - H67-3 (E1) | Stop light switch | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | 0 to 1.5 V | ||
| A31-8 (LIN3) - H67-3 (E1) | LIN communication signal
(A/C inverter, battery state sensor) |
Ignition switch ON (READY) | Pulse generation |
| A31-11 (+B1) - H67-3 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| A31-12 (OPM2) - H67-3 (E1) | OIL PMP relay | Ignition switch ON (READY), engine stopped | 11 to 14 V |
| A31-14 (HMCL) - H67-3 (E1) | Communication signal | Ignition switch ON | Pulse generation
(Waveform 1) |
| A31-15 (DB2) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in D or S | 6.0 to 14 V |
| Ignition switch ON, shift lever not in D or S | 0 to 1.5 V | ||
| A31-16 (PR) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in P or R | 6.0 to 14 V |
| Ignition switch ON, shift lever not in P or R | 0 to 1.5 V | ||
| A31-18 (PSFT) - H67-3 (E1) | Shift lever position sensor power source | Ignition switch ON (ACC) | 6.0 to 14 V |
| A31-20 (BL) - H67-3 (E1) | Back-up light relay | Ignition switch ON, shift lever in R | 11 to 14 V |
| A31-21 (OPM1) - H67-3 (E1) | Oil pump with motor assembly signal | Ignition switch ON (READY), engine stopped | Pulse generation
(Waveform 2) |
| A31-22 (NOPM) - H67-3 (E1) | Oil pump with motor assembly signal | Ignition switch ON (READY), engine stopped | Pulse generation
(Waveform 2) |
| A31-24 (VCPA) - A31-37 (EPA) | Accelerator pedal sensor assembly power source (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A31-26 (VCP2) - A31-25 (EPA2) | Accelerator pedal sensor assembly power source (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| A31-28 (P) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in P | 6.0 to 14 V |
| Ignition switch ON, shift lever not in P | 0 to 1.5 V | ||
| A31-29 (N) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in N | 6.0 to 14 V |
| Ignition switch ON, shift lever not in N | 0 to 1.5 V | ||
| A31-30 (PNB) - H67-3 (E1) | Shift lever position signal | Ignition switch ON, shift lever in P or N | 6.0 to 14 V |
| A31-33 (NIWP) - H67-3 (E1) | Inverter water pump assembly signal | Ignition switch ON (READY) | Pulse generation
(Waveform 3) |
| A31-34 (IWP) - H67-3 (E1) | Inverter water pump assembly signal | Ignition switch ON (READY) | Pulse generation
(Waveform 3) |
| A31-36 (VPA) - A31-37 (EPA) | Accelerator pedal sensor assembly (for accelerator pedal position detection) | Ignition switch ON, accelerator pedal released | 0.4 to 1.4 V |
| Ignition switch ON, engine stopped, shift lever in P, accelerator pedal fully depressed | 2.6 to 4.5 V | ||
| A31-38 (VPA2) - A31-25 (EPA2) | Accelerator pedal sensor assembly (for accelerator pedal sensor malfunction detection) | Ignition switch ON, accelerator pedal released | 1.0 to 2.2 V |
| Ignition switch ON, engine stopped, shift lever in P, accelerator pedal fully depressed | 3.4 to 5.3 V | ||
| A31-40 (TTA) - A31-39 (ETTA) | Transmission fluid temperature sensor | Ignition switch ON, temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON, temperature 60°C (140°F) | 2.2 to 3.2 V | ||
| A31-42 (RMT) - A31-43 (RMTG) | Rear motor temperature sensor | Ignition switch ON, temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON, temperature 60°C (140°F) | 2.2 to 3.2 V | ||
| A31-46 (MMT) - A31-45 (MMTG) | Motor temperature sensor | Ignition switch ON, temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON, temperature 60°C (140°F) | 2.2 to 3.2 V | ||
| A31-48 (GMT) - A31-47 (GMTG) | Generator temperature sensor | Ignition switch ON, temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON, temperature 60°C (140°F) | 2.2 to 3.2 V | ||
| A32-5 (ILK) - H67-3 (E1) | Interlock switch | Ignition switch ON, service plug grip installed correctly | 0 to 1.5 V |
| Ignition switch ON, service plug grip not installed | 11 to 14 V | ||
| A32-7 (CA3P) - H67-3 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 4) |
| A32-8 (CA1L) - H67-3 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 5) |
| A32-9 (CA4H) - H67-3 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 6) |
| A32-13 (SMRG) - A32-12 (E01) | System main relay operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 7) |
| A32-15 (SMRP) - A32-12 (E01) | System main relay operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 7) |
| A32-16 (SMRB) - A32-12 (E01) | System main relay operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 7) |
| A32-20 (CA3N) - H67-3 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 4) |
| A32-21 (CA1H) - H67-3 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 5) |
| A32-22 (CA4L) - H67-3 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 6) |
| A32-25 (PLKC) - H67-3 (E1) | Shift lock release request signal | Ignition switch ON (READY), brake pedal depressed | 11 to 14 V |
| Ignition switch ON (READY), brake pedal released | 0 to 1.5 V | ||
| A32-28 (ST1-) - H67-3 (E1) | Stop light switch signal | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 11 to 14 V | ||
| A32-29 (ACCI) - H67-3 (E1) | ACC relay | Ignition switch ON (ACC) | 11 to 14 V |
| A32-35 (IG2) - H67-3 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| H67-1 (+B2) - H67-3 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| H67-4 (ST2) - H67-3 (E1) | Starter signal | Ignition switch ON | 0 to 1.5 V |
| H67-7 (INDR) - H67-3 (E1) | Shift position indicator signal | Ignition switch ON, shift lever in R | 0 to 3.2 V |
| Ignition switch ON, shift lever not in R | 11 to 14 V | ||
| H67-8 (INDD) - H67-3 (E1) | Shift position indicator signal | Ignition switch ON, shift lever in D | 0 to 3.2 V |
| Ignition switch ON, shift lever not in D | 11 to 14 V | ||
| H67-11 (SFTD) - H67-3 (E1) | Transmission control | Ignition switch ON, shift lever in S | 11 to 14 V |
| Ignition switch ON, shift lever in (-) or shift paddle switch LH (-) operated | 0 to 1.5 V | ||
| H67-19 (INDP) - H67-3 (E1) | Shift position indicator signal | Ignition switch ON, shift lever in P | 0 to 3.2 V |
| Ignition switch ON, shift lever not in P | 11 to 14 V | ||
| H67-20 (INDM) - H67-3 (E1) | Shift position indicator signal | Ignition switch ON, shift lever in S | 0 to 3.2 V |
| Ignition switch ON, shift lever not in S | 11 to 14 V | ||
| H67-21 (INDN) - H67-3 (E1) | Shift position indicator signal | Ignition switch ON, shift lever in N | 0 to 3.2 V |
| Ignition switch ON, shift lever not in N | 11 to 14 V | ||
| H67-24 (SFTU) - H67-3 (E1) | Transmission control | Ignition switch ON, shift lever in S | 11 to 14 V |
| Ignition switch ON, shift lever in (+) or shift paddle switch RH (+) operated | 0 to 1.5 V | ||
| H67-25 (M) - H67-3 (E1) | Transmission control | Ignition switch ON, shift lever in S | 11 to 14 V |
| Ignition switch ON, shift lever not in S | 0 to 1.5 V | ||
| H67-27 (BATT) - H67-3 (E1) | Constant power source | Ignition switch ON | 11 to 14 V |
| Ignition switch ON (READY) | 11 to 15.5 V | ||
| H67-33 (EVSW) - H67-3 (E1) | EV drive mode switch (pattern select switch assembly) | Ignition switch ON, EV drive mode switch (pattern select switch assembly) not operated | 11 to 14 V |
| Ignition switch ON, EV drive mode switch (pattern select switch assembly) being pushed and held | 0 to 1.5 V | ||
| H67-36 (ALSD) - H67-3 (E1) | TRAIL mode switch (pattern select switch) signal | Ignition switch ON, TRAIL mode switch (pattern select switch) signal not operated | 11 to 14 V |
| Ignition switch ON, TRAIL mode switch (pattern select switch) signal being pushed and held | 0 to 1.5 V | ||
| H67-37 (DMS-) - H67-3 (E1) | Drive mode select switch (No. 1 pattern select switch assembly) signal | Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) not turned | 11 to 14 V |
| Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) backward and held | 0 to 1.5 V | ||
| H67-38 (DMS+) - H67-3 (E1) | Drive mode select switch (No. 1 pattern select switch assembly) signal | Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) not turned | 11 to 14 V |
| Ignition switch ON, Drive mode select switch (No. 1 pattern select switch assembly) forward and held | 0 to 1.5 V | ||
| H67-44 (IGB) - H67-3 (E1) | Power source | Ignition switch ON | 11 to 14 V |
Oscilloscope waveforms
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.
Waveform 1 (Communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: A31-4 (HMCH) - H67-3 (E1)
CH2: A31-14 (HMCL) - H67-3 (E1) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 2 (Oil pump with motor assembly signal)
| Item | Content |
|---|---|
| Terminal | CH1: A31-21 (OPM1) - H67-3 (E1)
CH2: A31-22 (NOPM) - H67-3 (E1) |
| Equipment Setting | 10 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON (READY), engine stopped |
The wavelength will vary with the operating speed of the oil pump.
Waveform 3 (Inverter water pump assembly signal)
| Item | Content |
|---|---|
| Terminal | CH1: A31-34 (IWP) - H67-3 (E1)
CH2: A31-33 (NIWP) - H67-3 (E1) |
| Equipment Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON (READY) |
The duty of the IWP signal and the frequency of the NIWP signal change according to the coolant (for inverter) temperature.
Waveform 4 (CAN communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: A32-7 (CA3P) - H67-3 (E1)
CH2: A32-20 (CA3N) - H67-3 (E1) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 5 (CAN communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: A32-21 (CA1H) - H67-3 (E1)
CH2: A32-8 (CA1L) - H67-3 (E1) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 6 (CAN Communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: A32-9 (CA4H) - H67-3 (E1)
CH2: A32-22 (CA4L) - H67-3 (E1) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 7 (System main relay operation signal)
| Item | Content |
|---|---|
| Terminal | CH1: A32-15 (SMRP) - A32-12 (E01)
CH2: A32-16 (SMRB) - A32-12 (E01) CH3: A32-13 (SMRG) - A32-12 (E01) |
| Equipment Setting | 10 V/DIV., 200 ms./DIV. |
| Condition | Ignition switch ON → Ignition switch ON (READY) |
BATTERY VOLTAGE SENSOR
| Terminal No.
(Symbol) |
Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| z12-1 (TC0) - z12-13 (GC0) | HV battery intake air temperature sensor | Ignition switch ON, HV battery intake air temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-2 (TB5) - z12-14 (GB5) | Battery temperature sensor 5 | Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-3 (TB4) - z12-15 (GB4) | Battery temperature sensor 4 | Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-4 (TB3) - z12-16 (GB3) | Battery temperature sensor 3 | Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-5 (TB2) - z12-17 (GB2) | Battery temperature sensor 2 | Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-6 (TB1) - z12-18 (GB1) | Battery temperature sensor 1 | Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-7 (TB0) - z12-19 (GB0) | Battery temperature sensor 0 | Ignition switch ON, HV battery temperature: -40 to 90°C (-40 to 194°F) | 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F)) |
| z12-9 (IB0) - z12-22 (GIB) | Battery current sensor | Ignition switch ON | 0.5 to 4.5 V |
| z12-10 (VIB) - z12-22 (GIB) | Power source for battery current sensor | Ignition switch ON | 4.5 to 5.5 V |
| y1-1 (IGCT) - y1-7 (GND) | Control signal | Ignition switch ON | 11 to 14 V |
| y1-2 (CA1H) - y1-7 (GND) | CAN communication signal | Ignition switch ON | Pulse generation
(waveform 1) |
| y1-3 (CA1L) - y1-7 (GND) | CAN communication signal | Ignition switch ON | Pulse generation
(waveform 1) |
| y1-5 (SI0) - y1-7 (GND) | Battery cooling blower (No. 0) operation signal | Cooling blower operating | Pulse generation
(Waveform 2) |
| Cooling blower not operating | 4.5 to 5.5 V | ||
| y1-6 (SI1) - y1-7 (GND) | Battery cooling blower (No. 1) operation signal | Cooling blower operating | Pulse generation
(Waveform 3) |
| Cooling blower not operating | 4.5 to 5.5 V | ||
| y1-7 (GND) - Body ground | Ground | Always (continuity check) | Below 1 Ω |
| y1-11 (FP0) - y1-7 (GND) | Battery cooling blower (No. 0) monitor signal | Cooling blower not operating | 0 Hz |
| Cooling blower operating | Pulse generation
(waveform 4) |
||
| y1-12 (FP1) - y1-7 (GND) | Battery cooling blower (No. 1) monitor signal | Cooling blower not operating | 0 Hz |
| Cooling blower operating | Pulse generation
(waveform 5) |
Oscilloscope waveforms
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.
Waveform 1 CAN communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: y1-2 (CA1H) - y1-7 (GND)
CH2: y1-3 (CA1L) - y1-7 (GND) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 2 (Battery cooling blower (No. 0) operation signal)
| Item | Content |
|---|---|
| Terminal | y1-5 (SI0) - y1-7 (GND) |
| Equipment Setting | 10 V/DIV., 1 ms./DIV. |
| Condition | Battery cooling blower assembly operating (Active Test of cooling fan being performed) |
The waveform will vary with the operating speed of the battery cooling blower assembly.
Waveform 3 (Battery cooling blower (No. 1) operation signal)
| Item | Content |
|---|---|
| Terminal | y1-6 (SI1) - y1-7 (GND) |
| Equipment Setting | 10 V/DIV., 1 ms./DIV. |
| Condition | Battery cooling blower assembly operating (Active Test of cooling fan being performed) |
The waveform will vary with the operating speed of the battery cooling blower assembly.
Waveform 4 (Battery cooling blower (No. 0) monitor signal)
| Item | Content |
|---|---|
| Terminal | y1-11 (FP0) - y1-7 (GND) |
| Equipment Setting | 2 V/DIV., 2 ms/DIV. |
| Condition | Battery cooling blower assembly operating (Active Test of cooling fan being performed) |
The frequency of the waveform will vary with the operating speed of the battery cooling blower assembly.
Waveform 5 (Battery cooling blower (No. 1) monitor signal)
| Item | Content |
|---|---|
| Terminal | y1-12 (FP1) - y1-7 (GND) |
| Equipment Setting | 2 V/DIV., 2 ms/DIV. |
| Condition | Battery cooling blower assembly operating (Active Test of cooling fan being performed) |
The frequency of the waveform will vary with the operating speed of the battery cooling blower assembly.