Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Parking Support Brake System (Reverse Only Type)) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0454817 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Parking Support Brake System (Reverse Only Type)) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Parking Support Brake System (Reverse Only Type))  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E399863E04
0.167,1.198 2.333,1.396 2.167,0.198 10 false from Engine Stop and Start ECU*2 5.354,1.74 6.583,2.24 1.229,0.5 10 false Clearance Warning ECU Assembly 5.448,0.469 5.76,0.667 0.313,0.198 10 false IG 5.458,1.229 5.771,1.427 0.313,0.198 10 false E 5.229,1.135 5.542,1.333 0.313,0.198 10 false 28 5.292,0.365 5.604,0.563 0.313,0.198 10 false 1 5.365,1.583 5.677,1.781 0.313,0.198 10 false H46 0.792,0.479 2.854,0.698 2.063,0.219 10 false from IG1-NO. 1 Relay*1 3.052,0.625 5.115,0.844 2.063,0.219 10 false ECU-IG1 NO. 4 0.313,2.042 2.479,2.24 2.167,0.198 10 false *1: w/o Stop and Start System 0.302,2.406 2.469,2.604 2.167,0.198 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE)
a.

Disconnect the H46 clearance warning ECU assembly connector.


E309541C44
1.417,0.229 1.917,0.479 0.5,0.25 0.292,0.594 0.458,0.594 0.458,0.594 0.479,0.99 true 0.104,0.531 0.563,0.729 0.458,0.198 10 false IG 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.51,0.281 1.969,0.479 0.458,0.198 10 false H46
*a Component with harness connected
(to Clearance Warning ECU Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H46-1 (IG) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
H46-1 (IG) - Body ground Ignition switch off Below 1 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-28 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR