Home › Vehicle Interior › MIRROR (INT) › DIGITAL REAR-VIEW MIRROR SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086890 MIRROR (INT) _0455056 DIGITAL REAR-VIEW MIRROR SYSTEM J

MIRROR (INT)  DIGITAL REAR-VIEW MIRROR SYSTEM  The Camera Indicator is not Displayed  


DESCRIPTION

Power is supplied to the inner rear view mirror assembly through the following circuit.

WIRING DIAGRAM

B596328E01
0.479,0.667 2.094,1.01 1.615,0.344 10 false from Auxiliary Battery 2.75,0.865 3.802,1.094 1.052,0.229 10 false ECU-DCC NO. 2 0.458,2.094 2,2.573 1.542,0.479 10 false from IG1-NO.1 Relay*1 2.781,2.281 3.75,2.521 0.969,0.24 10 false ECU-IG1 NO. 4 4.854,4.125 5.167,4.323 0.313,0.198 10 false R1 4.854,4.292 6.906,4.51 2.052,0.219 10 false Inner Rear View Mirror Assembly 5.458,0.667 5.771,0.865 0.313,0.198 10 false +B 5.469,2.094 5.781,2.292 0.313,0.198 10 false IG 5.469,3.49 5.625,3.688 0.156,0.198 10 false E 5.281,0.552 5.438,0.75 0.156,0.198 10 false 6 5.281,1.958 5.438,2.156 0.156,0.198 10 false 1 5.271,3.375 5.427,3.573 0.156,0.198 10 false 2 0.521,2.74 1.906,3.188 1.385,0.448 10 false from Engine Stop and Start ECU*2 0.417,4.052 4.854,4.25 4.438,0.198 10 false *1: w/o Stop and Start System 0.417,4.396 4.854,4.594 4.438,0.198 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - AUXILIARY BATTERY)
a.
B503769C50
1.51,0.25 1.917,0.51 0.406,0.26 0.75,1.885 0.958,1.885 0.958,1.885 1.313,1.531 true 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 1.625,0.292 2.083,0.49 0.458,0.198 10 false R1 0.542,1.802 0.854,2 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


Disconnect the inner rear view mirror assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R1-6 (+B) - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - IG POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - IG POWER SUPPLY)
a.
B503769C32
1.51,0.25 1.917,0.51 0.406,0.26 0.75,0.875 0.958,0.875 0.958,0.875 1.313,1.25 true 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 1.625,0.292 2.083,0.49 0.458,0.198 10 false R1 0.542,0.792 0.854,0.99 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


Disconnect the inner rear view mirror assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R1-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BODY GROUND)
a.
B503769C33
1.51,0.25 1.917,0.51 0.406,0.26 0.802,0.75 1.01,0.75 1.01,0.75 1.5,1.25 true 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 1.625,0.292 2.083,0.49 0.458,0.198 10 false R1 0.594,0.667 0.906,0.865 0.313,0.198 10 false E
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


Disconnect the inner rear view mirror assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INNER REAR VIEW MIRROR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR