Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419213 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, or when the communication ID codes do not match, the ECM stores this DTC.

*1: w/ ID Code Box

*2: w/o ID Code Box


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*1):
·

A malfunction is detected in the communication or communication lines between the ECM and ID code box (immobiliser code ECU)*2 or certification ECU (smart key ECU assembly)*3.

·

The communication ID codes of the ECM and ID code box (immobiliser code ECU)*2 or certification ECU (smart key ECU assembly)*3 do not match.


·

ID code box (immobiliser code ECU)*2

·

Certification ECU (smart key ECU assembly)*3

·

ECM

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: w/ ID Code Box

*3: w/o ID Code Box


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

w/ ID Code Box


B463090E56
0.979,2.896 1.438,3.094 0.458,0.198 10 false ECM 0.5,2.896 1.958,3.198 1.458,0.302 10 false A28 5.292,2.896 5.75,3.094 0.458,0.198 10 false H53 5.979,0.24 6.438,0.438 0.458,0.198 10 false 12 V 1.125,1.375 1.583,1.573 0.458,0.198 10 false 12 V 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.948 2.208,1.167 0.583,0.219 10 false IMO 1.688,1.865 2.146,2.063 0.458,0.198 10 false IMI 1.979,0.938 2.969,1.25 0.99,0.313 10 false 45 1.979,1.865 3.302,2.125 1.323,0.26 10 false 59 5.292,3.063 6.865,3.458 1.573,0.396 10 false ID Code Box (Immobiliser Code ECU)


w/o ID Code Box


B463090E80
0.979,2.896 1.438,3.094 0.458,0.198 10 false ECM 0.5,2.896 1.958,3.198 1.458,0.302 10 false A28 5.292,2.896 5.75,3.094 0.458,0.198 10 false A19 5.979,0.24 6.438,0.438 0.458,0.198 10 false 12 V 1.125,1.375 1.583,1.573 0.458,0.198 10 false 12 V 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.948 2.208,1.167 0.583,0.219 10 false IMO 1.688,1.865 2.146,2.063 0.458,0.198 10 false IMI 1.979,0.938 2.969,1.25 0.99,0.313 10 false 45 1.979,1.865 3.302,2.125 1.323,0.26 10 false 59 5.292,3.063 6.823,3.448 1.531,0.385 10 false Certification ECU (Smart Key ECU Assembly)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, refer to Service Bulletin.

*1: w/ ID Code Box

*2: w/o ID Code Box


·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279986 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Result Proceed to
NEXT (w/ ID Code Box) A
NEXT (w/o ID Code Box) B



A

2.CHECK ECM (TERMINAL EFII)

B

8.CHECK ECM (TERMINAL EFII)
2.CHECK ECM (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

C379326C30
3.26,0.083 3.677,0.333 0.417,0.25 3.198,3.552 3.031,3.552 3.031,3.552 3.031,3.042 true 2.667,3.563 2.833,3.563 2.833,3.563 2.833,3.042 true 3.906,1.49 3.74,1.49 3.74,1.49 3.521,0.938 true 2.458,0.302 2.771,0.458 0.313,0.156 10 false *a 2.854,2.052 3.167,2.208 0.313,0.156 10 false *b 2.51,3.469 2.823,3.625 0.313,0.156 10 false *c 3.24,3.479 3.552,3.635 0.313,0.156 10 false *d 0.854,3 1.167,3.156 0.313,0.156 10 false GND 3.948,1.406 4.313,1.583 0.365,0.177 10 false EFII 3.344,0.115 4.052,0.552 0.708,0.438 10 false H53
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H53-3 (EFII) - Body ground Ignition switch ON 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

3.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

B

6.CHECK ECM

C

3.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

C379327C56
3.323,0.052 3.74,0.302 0.417,0.25 3.344,0.833 2.844,1.26 2.844,1.26 2.698,1.26 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 2.573,0.25 2.885,0.406 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.865,2.99 1.177,3.146 0.313,0.156 10 false GND 3.396,0.094 3.813,0.323 0.417,0.229 10 false H53 2.344,1.177 2.76,1.375 0.417,0.198 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
H53-4 (EFIO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.


b.

Check that the engine can be started 5 seconds after the ignition switch turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

6.CHECK ECM
a.

Disconnect the A28 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-45 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the H53 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H53-3 (EFII) - A28-45 (IMO) Always Below 1 Ω
H53-3 (EFII) or A28-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK ECM (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

B473425C08
2.052,0.25 2.469,0.5 0.417,0.25 3.292,4.573 3.104,4.573 3.104,4.573 3.104,3.927 false 2.729,4.573 2.917,4.573 2.917,4.573 2.917,3.927 false 2.865,2.073 2.677,2.073 2.677,2.073 2.677,1.031 true 0.198,0.229 0.51,0.427 0.313,0.198 10 false *a 0.948,3.885 1.583,4.26 0.635,0.375 10 false GND 2.906,1.99 3.542,2.365 0.635,0.375 10 false EFII 2.958,2.99 3.271,3.188 0.313,0.198 10 false *b 2.583,4.479 2.896,4.677 0.313,0.198 10 false *c 3.323,4.49 3.635,4.688 0.313,0.198 10 false *d 2.135,0.292 2.771,0.667 0.635,0.375 10 false A19
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
A19-3 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal EFII stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

B

12.CHECK ECM

C

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B473424C16
2.042,0.25 2.458,0.5 0.417,0.25 3.021,4.594 3.208,4.594 3.208,4.594 3.208,4.073 false 3.573,4.594 3.385,4.594 3.385,4.594 3.385,4.073 false 2.781,2.125 2.594,2.125 2.594,2.125 2.594,1.063 true 0.104,0.271 0.417,0.427 0.313,0.156 10 false *a 3.26,3.042 3.573,3.198 0.313,0.156 10 false *b 2.885,4.5 3.198,4.656 0.313,0.156 10 false *c 3.594,4.5 3.906,4.656 0.313,0.156 10 false *d 2.115,0.292 2.427,0.448 0.313,0.156 10 false A19 0.896,4.021 1.49,4.302 0.594,0.281 10 false GND 2.833,2.031 3.427,2.313 0.594,0.281 10 false EFIO
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
A19-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

10.REGISTER ECU COMMUNICATION ID

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.


b.

Check that the engine can be started 5 seconds after the ignition switch turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

12.CHECK ECM
a.

Disconnect the A28 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-45 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A19 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-3 (EFII) - A28-45 (IMO) Always Below 1 Ω
A19-4 (EFIO) - A28-59 (IMI) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR