Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419213 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 is stuck high, the ECM will store this DTC.

*1: w/ ID Code Box

*2: w/o ID Code Box


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*2 or certification ECU (smart key ECU assembly)*3 is stuck high. (1 trip detection logic*1)
·

ID code box (immobiliser code ECU)*2

·

Certification ECU (smart key ECU assembly)*3

·

ECM

·

Wire harness or connector


DTC output confirmation operation:

Turn the ignition switch to ON and wait 6 seconds.



*1: Only output while a malfunction is present.

*2: w/ ID Code Box

*3: w/o ID Code Box


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

w/ ID Code Box


B463091E55
1.135,1.698 1.594,1.896 0.458,0.198 10 false ECM 0.646,1.698 2.063,1.979 1.417,0.281 10 false A28 0.792,0.219 1.25,0.417 0.458,0.198 10 false 12 V 1.865,0.708 2.323,0.906 0.458,0.198 10 false IMI 2.177,0.708 3.281,1.021 1.104,0.313 10 false 59 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.688 5.583,1.885 0.458,0.198 10 false H53 5.125,1.854 6.698,2.302 1.573,0.448 10 false ID Code Box (Immobiliser Code ECU)


w/o ID Code Box


B463091E79
1.135,1.698 1.594,1.896 0.458,0.198 10 false ECM 0.646,1.698 2.063,1.979 1.417,0.281 10 false A28 0.792,0.219 1.25,0.417 0.458,0.198 10 false 12 V 1.865,0.708 2.323,0.906 0.458,0.198 10 false IMI 2.177,0.708 3.281,1.021 1.104,0.313 10 false 59 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.698 5.583,1.896 0.458,0.198 10 false A19 5.125,1.854 6.656,2.323 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, refer to Service Bulletin.

*1: w/ ID Code Box

*2: w/o ID Code Box


·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279A12 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.

*1: w/ ID Code Box

*2: w/o ID Code Box


OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK WHETHER ENGINE STARTS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (w/ ID Code Box) B
NG (w/o ID Code Box) C



A

B

3.CHECK ECM (TERMINAL EFIO)

C

6.CHECK ECM (TERMINAL EFIO)
3.CHECK ECM (TERMINAL EFIO)
a.
B503616C08
1.521,0.333 1.938,0.583 0.417,0.25 1.021,1.604 1.229,1.604 1.229,1.604 1.521,1.177 true 0.156,0.115 0.927,0.76 0.771,0.646 10 false *a 1.604,0.375 2.375,1.021 0.771,0.646 10 false H53 0.667,1.521 1.354,1.781 0.688,0.26 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H53-4 (EFIO) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

NG

5.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
4.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

C379327C57
3.323,0.042 3.74,0.292 0.417,0.25 3.344,0.833 2.844,1.26 2.844,1.26 2.698,1.26 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 2.625,0.25 2.885,0.458 0.26,0.208 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.156,3.146 0.313,0.156 10 false GND 3.406,0.083 4.01,0.479 0.604,0.396 10 false H53 2.344,1.177 2.76,1.375 0.417,0.198 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H53-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

5.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the A28 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H53-4 (EFIO) - A28-59 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (TERMINAL EFIO)
a.
B557052C09
1.458,0.073 1.875,0.323 0.417,0.25 2.313,1.813 2.115,1.813 2.115,1.813 2.115,0.979 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.542,0.104 1.854,0.302 0.313,0.198 10 false A19 2.365,1.729 3.292,1.927 0.927,0.198 10 false EFIO
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A19-4 (EFIO) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

NG

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B473424C17
2.042,0.25 2.458,0.5 0.417,0.25 3.021,4.594 3.208,4.594 3.208,4.594 3.208,4.073 false 3.573,4.594 3.385,4.594 3.385,4.594 3.385,4.073 false 2.781,2.125 2.594,2.125 2.594,2.125 2.594,1.063 true 0.104,0.271 0.417,0.427 0.313,0.156 10 false *a 3.26,3.042 3.573,3.198 0.313,0.156 10 false *b 2.885,4.5 3.198,4.656 0.313,0.156 10 false *c 3.594,4.5 3.906,4.656 0.313,0.156 10 false *d 2.115,0.292 2.427,0.448 0.313,0.156 10 false A19 0.896,4.021 1.49,4.302 0.594,0.281 10 false GND 2.833,2.031 3.427,2.313 0.594,0.281 10 false EFIO
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
A19-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A28 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-4 (EFIO) - A28-59 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR