Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E410046E08
0.438,0.594 2.271,0.792 1.833,0.198 10 false from Auxiliary Battery*1 0.771,1.698 2.917,1.896 2.146,0.198 10 false from ACC Relay*1 0.552,2.802 3.615,3 3.063,0.198 10 false from IG1-NO. 1 Relay 3.385,0.75 4.333,1.01 0.948,0.26 10 false RADIO NO. 2 3.448,1.865 4.521,2.063 1.073,0.198 10 false ECU-ACC 3.313,2.979 5.302,3.177 1.99,0.198 10 false ECU-IG1 NO. 4 5.469,0.594 5.781,0.792 0.313,0.198 10 false H1 5.469,2.813 5.781,3.01 0.313,0.198 10 false H2 5.5,0.385 5.656,0.583 0.156,0.198 10 false 4 5.469,1.5 5.781,1.698 0.313,0.198 10 false 15 5.458,2.615 5.771,2.813 0.313,0.198 10 false 19 5.5,3.156 5.656,3.354 0.156,0.198 10 false 1 5.792,0.594 6.25,0.792 0.458,0.198 10 false +B1 5.792,1.708 6.406,1.906 0.615,0.198 10 false ACC1 5.802,2.802 6.115,3 0.313,0.198 10 false IG 5.792,3.375 6.406,3.573 0.615,0.198 10 false GND1 5.542,3.813 6.75,4.458 1.208,0.646 10 false Radio and Display Receiver Assembly 0.885,1.146 3.479,1.448 2.594,0.302 10 false from Engine Stop and Start ECU*2 0.729,3.813 2.823,4.229 2.094,0.417 10 false *1: w/o Stop and Start System 0.885,2.271 3.427,2.656 2.542,0.385 10 false from Engine Stop and Start ECU*2 0.729,4.188 2.813,4.531 2.083,0.344 10 false *2: w/ Stop and Start System 5.469,1.708 5.781,1.906 0.313,0.198 10 false H1 5.469,3.385 5.781,3.583 0.313,0.198 10 false H1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the H1 and H2 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H1-4 (+B1) - H1-1 (GND1)*1 Ignition switch off 11 to 14 V
H1-4 (+B1) - H1-1 (GND1)*2 Always 11 to 14 V*3
10.5 to 16 V*4
H1-15 (ACC1) - H1-1 (GND1) Ignition switch ACC 11 to 14 V*3
10.5 to 16 V*4
H2-19 (IG) - H1-1 (GND1) Ignition switch ON 11 to 14 V


*1: for HV Model

*2: for Gasoline Model

*3: w/o Stop and Start System

*4: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C