Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE CONTROL) › SFI SYSTEM › 2020.11–2021.10
RM37A0E _51 Engine / Hybrid System _086905 A25A-FXS, A25B-FXS ENGINE CONTROL _0419404 SFI SYSTEM C

A25A-FXS, A25B-FXS ENGINE CONTROL  SFI SYSTEM  P05B112  Active Grille Air Shutter "B" Circuit Short to Battery  P05B114  Active Grille Air Shutter "B" Circuit Short to Ground or Open  P05B131  Active Grille Air Shutter "B" No Signal  


DESCRIPTION

Refer to DTC P059F73.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>P059F73

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05B112 Active Grille Air Shutter "B" Circuit Short to Battery All of the following conditions are met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

The auxiliary battery voltage is 10.5 to 16 V.

·

Grille shutter opening or closing operation is being performed.

·

The Hall IC1 signal or Hall IC2 signal is stuck on the high side when the other signal is received normally.


Swing grille actuator assembly Does not come on DTC stored SAE Code: P05B3
P05B114 Active Grille Air Shutter "B" Circuit Short to Ground or Open All of the following conditions are met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

The auxiliary battery voltage is 10.5 to 16 V.

·

Grille shutter opening or closing operation is being performed.

·

The Hall IC1 signal or Hall IC2 signal is stuck on the low side when the other signal is received normally.


Swing grille actuator assembly Does not come on DTC stored SAE Code: P05B4
P05B131 Active Grille Air Shutter "B" No Signal Both of the following conditions are met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·

Grille shutter opening or closing operation is being performed.

·

The Hall IC1 signal and Hall IC2 signal are not received while the grille shutter motor (swing grille actuator assembly) is operating.


Swing grille actuator assembly Does not come on DTC stored SAE Code: P05B2

HINT:

*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.


MONITOR DESCRIPTION

1.

Hall IC Signal Malfunction

If the grille shutter ECU (swing grille actuator assembly) detects a stuck high or stuck low signal from either hall IC1 or hall IC2, it will output a malfunction signal to the ECM and the ECM will store a DTC.

A380356E01
0.063,0.063 2.354,0.271 2.292,0.208 10 false Example: Hall IC2 Signal Malfunction 0.135,1.063 1.073,1.26 0.938,0.198 10 false Hall IC1 Signal 0.135,1.521 1.073,1.719 0.938,0.198 10 false Hall IC2 Signal 5.625,1.521 7.052,1.698 1.427,0.177 10 false Stuck High Malfunction 5.635,1.896 7.052,2.083 1.417,0.188 10 false Stuck Low Malfunction 5.677,1.052 6.802,1.271 1.125,0.219 10 false Normal Signal

Detection Condition DTC No.
Short to +B (Stuck High) P05B112 (Active Grille Air Shutter "B" Circuit Short to Battery)
Open or Short to Ground (Stuck Low) P05B114 (Active Grille Air Shutter "B" Circuit Short to Ground or Open)

2.

Hall IC Signal Reception Malfunction

If the grille shutter ECU (swing grille actuator assembly) detects a stuck high or stuck low signal from both hall IC1 and hall IC2, it will output a malfunction signal to the ECM and the ECM will store a DTC.

A376917E02
0.167,0.656 1.396,0.979 1.229,0.323 10 false Grille Shutter Motor Operation 0.094,1.75 1.385,1.896 1.292,0.146 10 false Hall IC1 Signal 0.104,2.281 1.396,2.448 1.292,0.167 10 false Hall IC2 Signal 1.479,0.802 2.604,1.031 1.125,0.229 10 false Normal Operation 2.813,1.094 3.677,1.281 0.865,0.188 10 false Stopped 3.719,0.823 4.802,1.177 1.083,0.354 10 false Normal Operation (2nd Attempt) 5.052,1.094 5.917,1.281 0.865,0.188 10 false Stopped 6.073,1.313 6.708,1.677 0.635,0.365 10 false Reverse Operation 6.417,3.219 7.146,3.583 0.729,0.365 10 false Malfunction Judgment

Detection Condition DTC No.
Abnormal Signal (Hall IC1 and Hall IC2) P05B131 (Active Grille Air Shutter "B" No Signal)


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.

9.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

10.

Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

11.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.


12.

Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

13.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



CAUTION / NOTICE / HINT

NOTICE:
·

In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

Result:
Proceed to
NEXT



NEXT

2.REPLACE SWING GRILLE ACTUATOR ASSEMBLY
2.REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NEXT

3.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING AND GRILL SHUTTER INITIALIZATION)
3.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING AND GRILL SHUTTER INITIALIZATION)
HINT:

When changing the grille shutter control mode and/or performing initialization by driving the vehicle, the grille shutter control mode can only be changed and initialization can only be performed if the grille shutter system is in maintenance mode.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION


a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

b.

According to the display on the GTS, perform Grille Shutter Initialization.

Body Electrical > Grill Shutter > Utility
Tester Display
Grille Shutter Initialization
50005 352 4467

c.

According to the display on the GTS, read the Data List and check that the value of Shutter Control State is "Normal" and Shutter Initialization is "Complete".

Body Electrical > Grill Shutter > Data List
Tester Display
Shutter Control State
Shutter Initialization
50003 352 10,29

Result:
Proceed to
NEXT



NEXT

END