Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C110000  Brake Pedal Position Sensor "A" Supply Voltage Malfunction  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C110000 Brake Pedal Position Sensor "A" Supply Voltage Malfunction When the voltage at terminal +BI1 is 7.3 V or more, the value of brake pedal stroke sensor 1 is invalid for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

WIRING DIAGRAM

C427351E01
4.885,0.667 5.354,0.906 0.469,0.24 10 false VSK1 4.885,1.292 5.344,1.521 0.458,0.229 10 false SKS1 4.875,1.917 5.375,2.208 0.5,0.292 10 false SKG1 4.625,0.458 4.938,0.656 0.313,0.198 10 false 16 4.688,1.073 5,1.271 0.313,0.198 10 false 3 4.625,1.688 4.938,1.885 0.313,0.198 10 false 18 4.552,2.135 4.865,2.333 0.313,0.198 10 false A44 4.542,2.302 6.979,2.667 2.438,0.365 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.74,0.448 3.052,0.646 0.313,0.198 10 false 4 2.74,4.531 3.052,4.729 0.313,0.198 10 false 3 2.74,3.906 3.052,4.104 0.313,0.198 10 false 1 2.74,3.292 3.052,3.49 0.313,0.198 10 false 2 2.74,1.073 3.052,1.271 0.313,0.198 10 false 6 2.74,1.688 3.052,1.885 0.313,0.198 10 false 5 0.344,5.052 0.656,5.25 0.313,0.198 10 false A43 0.333,5.219 2.792,5.583 2.458,0.365 10 false Brake Pedal Stroke Sensor Assembly 2.24,0.677 2.708,0.917 0.469,0.24 10 false VCSK 2.25,1.292 2.708,1.521 0.458,0.229 10 false SKS1 2.313,1.906 2.813,2.198 0.5,0.292 10 false SKG 2.271,3.521 2.75,3.781 0.479,0.26 10 false VSK2 2.26,4.135 2.729,4.406 0.469,0.271 10 false SKS2 2.25,4.76 2.771,5.042 0.521,0.281 10 false SKG2 4.448,5.125 6.927,5.531 2.479,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.458,4.958 4.771,5.156 0.313,0.198 10 false A57 4.865,3.521 5.344,3.781 0.479,0.26 10 false VSK2 4.854,4.135 5.323,4.406 0.469,0.271 10 false SKS2 4.854,4.76 5.375,5.042 0.521,0.281 10 false SKG2 4.604,3.292 4.917,3.49 0.313,0.198 10 false 25 4.594,3.906 4.906,4.104 0.313,0.198 10 false 10 4.604,4.531 4.917,4.729 0.313,0.198 10 false 26 6.458,1.198 6.771,1.396 0.313,0.198 10 false IC 6.438,4.052 6.75,4.25 0.313,0.198 10 false IC 0.5,1.094 0.875,1.698 0.375,0.604 10 false HALL IC1 0.469,3.969 0.844,4.573 0.375,0.604 10 false HALL IC2

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A43 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-3 (SKS1) - A43-6 (SKS1) Always Below 1 Ω
A44-3 (SKS1) or A43-6 (SKS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR