Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  TERMINALS OF ECU  


TERMINAL INSPECTION


a.

Disconnect the A39 connector and measure the voltage or resistance on the wire harness side.

C425606C05
3.354,0.323 3.781,0.573 0.427,0.25 0.177,0.198 0.594,0.573 0.417,0.375 10 false *a 3.448,0.365 3.865,0.74 0.417,0.375 10 false A39
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A39-1 (GND1) - Body ground Skid control ECU (brake actuator assembly) ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A39-2 - - -
A39-3 - - -
A39-4 (RL-) Rear speed sensor LH (-) signal input - -
A39-5 (RL+) Rear speed sensor LH (+) power supply output - -
A39-6 (FR-) Front speed sensor RH (-) signal input - -
A39-7 (FR+) Front speed sensor RH (+) power supply output - -
A39-8 - - -
A39-9 (CSW) - Body ground VSC OFF switch input VSC OFF switch is pushed → released Below 1 Ω → 10 kΩ or higher
A39-10 - - -
A39-11 (STP) - Body ground Stop light switch assembly input Stop light switch assembly on → off
(brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A39-12 - - -
A39-13 - - -
A39-14 (+BS) - Body ground Solenoid relay power supply Always 11 to 14 V
A39-15 - - -
A39-16 - - -
A39-17 - - -
A39-18 (SP1) - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A39-19 (RR-) Rear speed sensor RH (-) signal input - -
A39-20 (RR+) Rear speed sensor RH (+) power supply output - -
A39-21 (FL-) Front speed sensor LH (-) signal input - -
A39-22 (FL+) Front speed sensor LH (+) power supply output - -
A39-23 - - -
A39-24 - - -
A39-25 - - -
A39-26 - - -
A39-27 (CANH) CAN communication line H - -
A39-28 (FSW+) - Body ground Brake pedal load sensing switch (brake pedal support assembly) input Brake pedal depressed → released 950 to 1050 Ω → 203 to 223 Ω
A39-29 - - -
A39-30 (GND2) - Body ground Pump motor ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A39-31 - - -
A39-32 (STPO) - Body ground Stop light control relay (stop light switch assembly) output Always 11 to 14 V
A39-33 - - -
A39-34 - - -
A39-35 (PKB) - Body ground Brake hold switch (electric parking brake switch assembly) input Brake hold switch (electric parking brake switch assembly) is pushed → released Below 1 Ω → 10 kΩ or higher
A39-36 - - -
A39-37 (STP2) - Body ground Stop light signal input Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A39-38 - - -
A39-39 - - -
A39-40 - - -
A39-41 - - -
A39-42 - - -
A39-43 (CANL) CAN communication line L - -
A39-44 (HDCS) - Body ground*3 Downhill assist control switch input Downhill assist control switch is pushed → released Below 1 Ω → 10 kΩ or higher
A39-45 (IG1) - Body ground ECU power supply input Ignition switch ON 10.5 to 16.0 V*1
11 to 14 V*2
A39-46 (BM) - Body ground Motor relay power supply Always 11 to 14 V

*1: w/ Stop and Start System

*2: w/o Stop and Start System

*3: for AWD