FREEZE FRAME DATA
Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
CHECK FREEZE FRAME DATA WHEN DTC WAS STORED
Freeze Frame Data is stored when a DTC is output.
Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Turn the ignition switch off.
Connect the GTS to the DLC3 and turn the ignition switch to ON.
Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Select a DTC to display the Freeze Frame Data.
Check the Freeze Frame Data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| IG1 Voltage Value | IG1 terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V*4
Ignition switch ON: 10.5 to 16 V*5 |
Changes in proportion to auxiliary battery voltage |
| BS1 Voltage Value | +BS terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Motor Power Supply Voltage | BM terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| FR Wheel Speed | Front speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa
Max.: 23.99 MPa |
Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| Master Cylinder Sensor Temperature | Master cylinder pressure sensor temperature | Min.: -80°C
Max.: 175°C |
Displays temperature master cylinder pressure sensor | - |
| M/C Sensor Grade | Master cylinder pressure sensor change (value detected by ECU) | Min.: -30 MPa/s
Max.: 225 MPa/s |
Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor (airbag sensor assembly) | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Value | Steering sensor | Min.: -3276.8°
Max.: 3276.7° |
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0° |
- |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Power Train Driving force | Powertrain drive torque | Min.: -327680 N
Max.: 327670 N |
- | - |
| Gear Position | Gear position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R | Actual gear position | - |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode /
Pressure hold mode / Pressure release mode / EPB lock mode |
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle acceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Vehicle Stop Time from IG ON | Time vehicle stopped after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Travel Distance from IG ON | Driving time after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Elapsed Time | Time elapsed after ignition switch turned to ON | Min.: 0.00 s
Max.: 100661.760 s |
- | - |
| MT2 | Motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
- | - |
| IG Switch | Ignition switch ON status | OFF / ON | - | - |
| Downhill Assist Control SW | Downhill assist control switch | OFF / ON | - | for AWD |
| Stop Light SW | Stop light switch assembly status
(STP or STP2 terminal input) |
OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake switch | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch (brake pedal support assembly) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (PKB terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (stop light switch assembly) status
(STP terminal input) |
OFF / ON | OFF: Stop light control relay (stop light switch assembly) off and brake pedal released
ON: Stop light control relay (stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
|
| TRC(TRAC) Control | TRC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| HAB Control | High power assist brake status | OFF / ON | OFF: During not control
ON: During control |
- |
| Fail Status | Brake booster failure status | OFF / ON | OFF: During not control
ON: During control |
- |
| Fail Control | Failure control status | OFF / ON | OFF: During not control
ON: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
w/ Pre-collision System |
| Stop Light Relay State for ECU Control | Stop light control relay (stop light switch assembly) status (STPO terminal output) (for ECU control) | OFF / ON | OFF: Stop light control relay (stop light switch assembly) off (stop light off)
ON: Stop light control relay (stop light switch assembly) on (stop light on) |
- |
| Engine Stop by Stop and Start System | Engine stopped by stop and start system status (for ECU control) | OFF / ON | OFF: Engine not stopped by stop and start control
ON: Engine stopped by stop and start control |
w/ Stop and Start System |
| Solenoid State for ECU Control | ABS solenoid relay status (for ECU control) | OFF / ON | OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating |
- |
| Motor State for ECU Control | ABS motor relay status (for ECU control) | OFF / ON | OFF: ABS motor relay not operating
ON: ABS motor relay operating |
- |
| Operation History of IG OFF while Vehicle is moving | History of ignition switch turned off when vehicle is in motion | OFF / ON | OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF
ON: VSC OFF switch ON |
|
| FR Speed Open | Front speed sensor RH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| FL Speed Open | Front speed sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RR Speed Open | Rear speed sensor RH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RL Speed Open | Rear speed sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| EFI Communication Open | ECM communication open detection | Normal / Under intermittent | Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected |
- |
| Yaw Rate Open | Yaw rate sensor (airbag sensor assembly) open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Deceleration Open | Acceleration sensor (airbag sensor assembly) open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Steering Open | Steering sensor open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| M/C Pressure Sensor Noise | Master cylinder pressure sensor noise detection | Normal / Under intermittent | Normal: Noise not detected
Under intermittent: Noise detected |
- |
| Brake Pedal Switch Open | Brake pedal load sensing switch (brake pedal support assembly) open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor (airbag sensor assembly) voltage open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| EFI Communication Invalid | ECM communication invalid detection | Normal / Under intermittent | Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected |
- |
| Master Cylinder Pressure Sensor Power Supply Open | Master cylinder pressure sensor power supply voltage status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Solenoid Power Supply Open | Solenoid power supply voltage status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Motor Power Supply Open | Motor power supply voltage status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Stop Switch Open | Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Stop and Start ECU Communication Open | Engine stop and start ECU communication open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
w/ Stop and Start System |
| Air Bag ECU Communication Open | Airbag sensor assembly open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Brake Hold Ready | Brake hold control permission status | Not in stand-by mode / Stand-by mode | Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated) |
- |
| FR Speed Signal Status | Front wheel RH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| FL Speed Signal Status | Front wheel LH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| RR Speed Signal Status | Rear wheel RH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
| RL Speed Signal Status | Rear wheel LH speed signal status | Normal / Fixed | Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck |
- |
*1: for entering Inspection Mode: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY
*2: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE
*3: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY
*4: w/o Stop and Start System
*5: w/ Stop and Start System
CLEAR FREEZE FRAME DATA
Clearing the DTC will also clear the Freeze Frame Data.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Clear the DTC and Freeze Frame Data.